Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I am using a nRF52 DK board and programming in python.
After performing a successful DFU over BLE i want my Target device to be disconnected from the nRF board so...
thanks for the answer on the previous post.
What I came to know from our firmware engineer was that your initial version of the Android app could not support
1. multiple...
I want to know 2 things about the nRF Mesh app:
1) Is it possible for the Mesh app to provision non-proxy nodes via the proxy nodes?
2) I think it's possible to subscribe...
I have a project using FreeRTOS with Tickless idle enabled, SDK 11.0.0 alpha and the S132 soft device. Currently the project is consuming ~6.5mA average, ~5.2mA if advertising...
Hi There,
I very new to Nordic BLE application and was looking for method to combine ble_app_beacon and ble_app_blinky togather and having both switching and running at...
Hi:
In the datasheet, there have a description
Input range = (+- 0.6 V or +-VDD/4)/Gain
for a example, if Gain = 2, reference = 0.6V,
input range = 0.6 / 2 = 0...
In the SDK12.3.0 example ble_app_hrs_rscs_relay I want to add a uart to this example I added the uart_init part and the nus part, referring to ble_app_uart. However, when...
Hello,
What are the maximum number of node our nrf52832 and 52840 can support for
Zigbee?
BLE?
Thread - 1000?
Would this number be dependent on the memory size?...
Hi, I am using nrf24L01 for my application. I have to question:
- Is it possible to bypass SB protocol (I take into account possible error in exchanged packets without preamble...
Hello All,
I am following this tutorial.
https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial
I have modified "nRF5_SDK_15...
Hi.
I refer to this document. Stopped at Step.B1 now.
If you go to that path using CMD and then type "make", you will see the following problem.
'make' is not an internal...
Hello,
In my project (nRF52, SDK14.2) I have spi data flash connected to the MCU.
I'm trying to use SPI transaction manager library (nrf_spi_mngr) and face few questions...
I don't know how to use nrf52840 dongle as a sniffer. I look at the official routine. It looks like it really doesn't function as a sniffer. Is this what it is. If not, how...
Hello, we are trying to get a new laptop compiling and debugging with an older project. The old project uses SDK5.2 and SoftDevice 6.2.1. When we open it we get the error...
Hi Everyone,
I have problem about debugging program which for my nRF52810 custom board. I am using SEGGER IDE. I changed ses_nrf52810_Vectors.s and system_nrf52810.c files...
