Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi community,
I read these articles about match network for antenna:
General PCB design guidelines for nRF53 series - nRF5x - Hardware design, test and measuring - Nordic...
Hi,
Like some other users, I face an issue migrating from ncs<2.6.0 to ncs 2.7.0 regarding radio notification.
I saw it is possible to use the PPI for the EGU IRQ to be...
Hello, I am using the Soft Device S140 7.3.0 with nRF5 SDK 17.1.0 and the nRF52820 as a peripheral in an NUS application. Initially, the transfer was slow but worked perfectly...
Using the nRF54L15 Development Board.
Did try to run the "nRF connect for desktop" - "Quick start"
I do not get a reply from the Board when doing one of the samples. ...
Hello!
Assume a BLE device already has Bluetooth qualification.
Does FOTA DFU requires new a Bluetooth qualification and additional fees if SoftDevice was updated too...
Hello, I am working on nrf52840 in which the BLE is not Advertising even after i am adding one paramter i just want to add the parameters at the time of adding the 2 parameters...
I am attempting to get the SMP server sample to work on some custom hardware in order to run a BLE FOTA. I'm using NCS version 2.6.1.
I'm able to build the SMP server sample...
Hi team,
I am using ncsv2.8.0, on our custom designed nrf52832 board.
Here I am trying to integrate i2c driver code for bme688 along with bsec library in peripheral_uart...
Hello,
i'm developing a custom board with nRF5340 (WLCSP package) that is very constrained in terms of space for a Bluetooth application. I looked on DevZone and i found...
I first tried nrfjprog which didn't work, but I know that's being retired so that wasn't entirely surprising. After that I moved on to testing 'nrfutil', specifically the...
I am building a BLE audio product that is based on the nRF5340. The application is largely based on the nrf5340_audio ncs example application, but I am modifying the the application...
Hi,
I am testing an actinius_icarus board V2.
I read data from senso BM68X every 500 ms, and publish on mqtt broker every 1 seconds. they are 256 bytes every sending....
Hi,
I am using NRF Cloud + coap comms to send data. However I have encountered payload size limitations that are not configurable via KConfig: sdk-nrf/subsys/net/lib/nrf_cloud...
Unable to find enough information to convert the raw values obtained from Thingy53 for RGB components.
Referred to BH1749NUC datasheet, Thingy53 sample code
Hi,
I am writing a custom i2c driver for an evaluation, when I ran the same i was getting exception:
during troubleshooting i scraped the entire custom driver and...
