Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
My task is to use MAX30003 WING and process ECG data using nRF5340 DK. I will use SPI protocol for doing it. I was following these 2 tutorials: Lesson 5 - Serial Peripheral...
I am using SDK v2.5.0 on custom board.
The board has an external 4MB flash chip.
I am wondering though which paritition will be used for the update process, and how that...
My project: I am developing a system consisting of a central and up to 20 peripherals based on the Multi-NUS protocol. Toolchain and SDK : NCS v2.6.1. Development target:...
Hello,
I have a project for the nRF52811 using the nRF Connect SDK. As I understand, it’s not recommended to modify the main .dts file directly; instead, changes should...
Hi Team,
Problem: I'm working on a project using the nRF52840 and nRF Connect SDK 2.2.0. I need to transfer some files from host over UART and store them in LittleFS. I...
We are experiencing interruptions in the audio, with noise similar to popping sounds.
When observing the waveform on the spectrum analyzer during the audio interruptions...
Hello I am trying to build the Zephyr mesh distributor sample on the nRF 52840 dongle It builds and runs just find on the nRF52840 DK But when I try to build for the dongle...
I made a custom board And I am running the segger example ble_app_blinky_pca10056_s140 But Even if I run log_init();, it returns error code 5 And even if I run timers_init...
Hi,
I have updated the device application firmware from nRF Connect SDK v2.6.1 to v2.7.0.
The firmware was working fine in v2.6.1 without issue. But the same firmware...
mcu: nrf5340
board: nrf5340dk_nrf5340_cpuapp
sdk: v2.6.1
When I configure CONFIG_BOARD_ENABLE_CPUNET to enable cpunet, there isn't an issue. However, when I configure...
Hi, I have been trying to use my esp host mcu with nrf5340dk as a controller.I am using the hci_uart application with CONFIG_BT_LL_ACS_NRF53 =y to include le audio support...
Hi All
I am experiencing an issue with the nRF DFU app (v2.7.0) on devices running both Android 11 and Android 14. The issue occurs when I attempt to perform a DFU update...
