Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello, I want to purchase cables to connect a Flasher Pro (cable should end on DB20 Female) to an nRF52-DK onto "Debug In" connector (cable should end on mini DB10 Female...
Hello, I am developing a solution based on nrf52-DK, using nRF52832.
I am trying to use JFlash to read Device Serial Number. I could read it with JLink , with command "mem32...
Hi, hope someone can help me.
The past 3-4 years I have used SDK 17.1.0 and SES for SW development where the SW is running on a nRF52840 SoC which is the heart of our product...
I'm working on a Docker image that includes a VS Code server for the purposes of workshops and training, and I'd like to install the nRF extensions (e.g. https://marketplace...
hi，bro
I want to support both BLE and GZLL simultaneously and perform the corresponding initialization work based on the value of a variable, mode . However, when I set...
Hi,
I have difficulties to sniff BLE packets with nRF52840 and wireshark between a remote controller and phone.
I can capture all the pairing process, I see DHKey exchange...
Greetings!
I am looking into Bluetooth Mesh, and the allowed radiated power according to Norwegian law. The general limit for 2.4GHz is 10mW, but if we utilize FHSS the...
Hello, I'm running into an issue with the "modem shell for NR+" application on a pair of nrf9131ek evaluation kits. The local sales rep. suggested that I reach out to Nordic...
Hello, I have a pair of nRF9142EK devices that I've been using to test DECT NR+. Now, I'd like to test out one of the boards with the cellular modem firmware for nRF9131EK...
Hi Support team,
I am using nRF9160 module and i want run two server on the module, one is modbus server and other is CoAP server. so is it possible to run both server...
When using the adafruit feather nrf52840 , the lowest I can seem to get power usage is around 400uA (including with the boards/nordic/poweroff sample ) .
This is my device...
Hello
I'm exploring the mesh dfu transfer, get some strange results
Here is the setup
1 distributor, 1 target
On the distributor I start the transfer with mesh models...
Hi,
I need to setup shell interface on both sides to exchange sensor data via uart.
The connection is as follow: cable 1: nRF52840DK Pin (TX - P1.02) → nRF9160DK Pin...
