Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hi there,
I must interact with an I2C slave that sends variable-length messages. The first byte of the transactions describes the length of the remaining bytes.
i2c_write_read_cb...
Dear Support,
we would like to know what is the total value of the capacitance and the inductance of the nRF52805 (for ATEX certification). I can not find this information...
We have project using the common Matter Code base from SDK 1.6.1 and using a variation of the code to act as a switch sensor device time. This seems to work pretty well; however...
I need to add tx power to my BLE advertising, but I need to ensure it is in the Scan Response only not the main AD PDU.
Also, I change the Tx power by code using the function...
I have a PCB made for my project. I want to read log from RTT. When I try the same software in the development kit, I can read from RTT. But when I want to read from the PCB...
Hi,
I have a proyect with the following memory requirements.
The current project has a propietary bootloader and bare-metal application. Therefore there is no Zephyr...
Hallo,
In the BSP startup files for the nRF5340 (gcc_startup_nrf5340_application.S & gcc_startup_nrf5340_network.S) the interrupt vectors USPTn_IRQHandler (n=0,...,3) are...
I hope someone can help me here with my question.
In my project we are using a nrf9160 with modem fw version 1.3.5. The application sends/receives data periodically (1 hour...
Hello and thanks for reading.
I have a critical problem with my device, and seeing as the problem is BLE related I figured I would ask your help as well. We are using the...
I'm using an nRF9160-DK board with the provided iBASIS SIM card. I followed the instructions here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.4.0/nrf/working_with_nrf...
Hi, I have a problem related to DFU OTA through BLE
When performing OTA through Bluetooth, I encountered the following issue:
Firmware built in the same build can be successfully...
Hello, I started looking into the DPPI from NRF5340 series and planning to integrate some functionality into an existing zephyr-based project. Specifically, I need timer-based...
Hey team,
We're having trouble with our device. It's been working fine, sending messages to our backend without a hitch. But after a while, it starts having problems connecting...
Hello.
The MCU of our new design will be the nRF52832.
I would like to know if it is ok to read the voltage of the battery that powers the system, nominal voltage of 3...
Dear support team,
1. Can mesh provisioner configure multiple devices at one time? For example, there are five unprovisioned devices within the provisioner's network. Can...
