Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hi,
I want to connect X-NUCLEO-NFC08A1 with ST25R3916B to nRF5340 board by adding a SPI node to device-tree source. After compiling and flashing the board, triggering interrupt...
Hi all,
NRF52832 NRF Connect 2.6.0
We need to configure interrupts on a GPIO on both edges. T here are several topics recommending to use GPIO_INT_TRIG_BOTH instead...
I'm getting started with nrf52840DK.
But when i connect my USB i get this error message:
i saw in this topic that when i press on the boot/reset long press when turning...
Hi all,
Could anyone share a code example for sending sensor data over BLE using the NUS Service in Zephyr RTOS? I'm new to this field and struggling to get data from the...
Hi
I use nRF7002-DK, SDK:Ｖ2.5.2 with zephyr driver, I need to send recieved data or command from uart, data type is using with hex byte array to send, from example , the...
Hi,
Because I wanted to add custom features to mcuboot, I had to use custom mcuboot.
I also used sysbuild for multi-image building.
The documentation tells me that...
Hello,
I am currently working with the nRF5340DK kit.
For my project, I need to incorporate some additional custom checks/code into the project's bootloader(MCUBoot)....
hardware:nrf5340dk
The above 45 pairs of IQ data are a set of data that I have received.The maximum amplitude of the IQ data I received seems to be only 128, which means...
Hi I am implementing dfu over modbus. Basically I managed to integrate all the steps (transport, set pending, restart, confirm).
What I'd like to do is to implement image...
Good afternoon,
I have recently purchased a PPK2. I have installed nrfConnect for desktop and Power Profiler on my Ubuntu 22.04 machine. I have connected the PPK2 and...
The example for LZ4 works fine, however I want to use the frame format and not block format.
Therefore I added #include "lz4frame.h" to my main.c and tried to use LZ4F_compressFrame...
My project is developed on nRF52840, it needs to communication with a mobile device through BLE, nRF52840 is as central. The mobile device starts BLE advertising, then, nRF52840...
hello guys, I want to use nrf52840 for my project is it possible to use ST Link for it. because I don't have SEGGER J-link ,if it is possible how can we use it please let...
Hello
I am trying to connect the nRF9160 -DK board to nRFCloud using CoAP protocol. I have written an application for this case. I tested my application with two different...
Hello
I'm trying to connect nrf7002EK with SPI3 with nrf52840DK,
NCS/Samples/WiFi/Shell, but I came up after Flash
The error shown in the image below
I would like...
