Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Summary
When a board's board.yml uses revision.format: number with exact: false , the fuzzy (fallback) revision matching silently fails and reports "Board revision not found...
Hi
We have a product that we are preparing for production.
The product needs to communicate with an Azure IOT Hub that only accepts RSA keys. We have used the device_credentials_installer...
Hi,
So we are currently using modem firmware nrf91x1_2.0.2 on a custom HW. I keep getting this error during boot and only after I wait for 30 mins I can connect to my...
Hello, I am developing with nRF5340 with my custom board. I observed a high current consumption when the network core is flashed with the ipc_radio image. I am developing...
Hi I want to use nRF9151DK and i have jio NB-IOT sim card.
I flashed asset tracker application from quick start and it is not working or connecting to internet this is the...
[Environ] nRF Connect SDK v3.2.3 nRF9151 (Custom board) VSCode (1.115.0) Board target: board/nrf9151/ns
When using the PTI firmware, the AT command resulted in an error...
I have a PCB with nRF52833 and nPM1304, I assembled 3 identical PCBs, 2 of them work 1 does not I am using 2 available Buck coveters, first outputs 1.8V for powering IC on...
Hi,
I a\m looking for your recommendation on screen to use with nRFLM20DK board to experiment with LVGL display. Assuming that latest version of nRF Connect SDK has everything...
Hi,
I am using nRF5340 (CPUAPP) with MCUboot and Partition Manager (pm_static.yml, CONFIG_PARTITION_MANAGER_ENABLED=y ).
Build and flash are successful, but during debug...
Dear Technical Support Team,
I have recently been developing with the nRF54L15-DK development board, using the official channel_sounding/cs_test example provided by Nordic...
I am designing a battery system with can charge or supply power via a USB-C PD controller. It will operate up to 20V. I want the option to connect this USB-C D+/D- to the...
Hello, I was able to flash the firmware built using the samples provided by the "nrf connect sdk" using VScode. But, I see failure when I tried to program the nRF54L15 with...
We're dimensioning the pullup resistors for the lowest possible standby current in system-OFF, but we cannot find any leakage current spec in the nRF54LM20 PS / datasheet...
When the USB stack and your local Filesystem code both try to control the flash chip simultaneously, the system will crash or trigger a HardFault, causing the restart.
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
