Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
I'll start off by saying, as a new developer, Nordic has made an absolute mess out of the docs. The default example 'TWI_sensor' starts with easyDMA enabled, meaning it defaults...
Hello,
I am using nrf5340 module with external hardware audio codec to test stereo audio output.
I use nrf5340 module as the headset to connect with Pixel 7 mobile phone...
Hi Nordic Team,
The default stream direction is undirectional, so I add CONFIG_STREAM_BIDIRECTIONAL=y in prj.conf, then use " python buildprog.py -c both -b debug -d both...
Hello,
We have a fitness application that employs concurrent use of ANT+ and BLE communications on an nRF52840, that we wish to port to the nRF5340. The product brief...
I created a custom bootloader based on the SDK 15.3.0 secure bootloader. At location 0xFF8 I defined the uicr bootloader start address as 0xE4000 but my bootloader actually...
Hello
I was trying to add BH1749 I2C Sensor for existing Mesh_Sensor example to get RGB values like shown in this Light_Sensor example. Couldn't decide how to do it and...
Hello all,
Environment: nRF52840-DK, NRF SDK V15.0.0, SoftDevice s140 v 6.0.0, ARMGCC building with Makefile
I am currently trying to combine the examples of the USB and...
On a 52840 USB stick, I successfully tested the "observer" demo app.
Now, I tried to extend it by enabling CONFIG_BT_EXT_ADV=y which is supposed to print some details about...
Hi, I got strange error which I can't to fix.
From time to time, I get the same readings from every function which counts the CPU cycles. They all base on DWT_CTRL. Board...
Using NCS SDK v2.1.0
Example Project: nrf/samples/bluetooth/peripheral_power_profiling
Building the example project gives build warnings:
Could you help me understand...
Hi,
I am trying to implement a Low Power Wireless technology to get sensor values from more than 10 devices at a time. On doing research, I found that the Thread Topology...
Hello, we have built a custom nRF9160 board with different populations for the GPS antenna, now we would like to do some tests to find out which variant offers the best signal...
Hi!
The posts I've found regarding this were quite old, and they mentioned features which then were coming.
So I'll ask anew: Is it possible to use AT-commands through...
Hello,
I would like to ask you if SoftDevice S132 v.7.x.x allows Master-initiated Feature Exchange procedure?
BLE Core spec: Vol6, Part B, Cap. 5.1.4.1.
I tried to find...
Hi everyone, I use nrf52833 to make dongle. My test found that after suspend of usb, I tried to enable ESB rx mode, but I couldn't receive rf data. What is the problem?The...
