Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi,
I have a quite controversial question I want to ask! I am new to the world of Nordic Semiconductor chipset and I need some information in order to decide which way to...
Hi I am trying to run the exampls of dwm1001 git file of ex_11b_leds on dwm1001 dev board using SES it gives me an error on Zephyr.h file , how can i connect to the nrf connect...
I developed a product for the customer with 9160. It used to run on the sdk of ncs1.2.0, and its fota function is normal; Now I have upgraded the sdk to ncs1.9.0, and found...
Hi!
Working on a BT peripheral device that will work in two modes depending on a runtime check at startup:
Sending data over BLE, running on battery (UART unused).
Sending...
Dear Support
I am developing a central application, scan and send out scanned packets via UART to host MCU, where I am thinking of calculate the advertising interval by...
Hi! I followed the recipe described on nRF Sniffer for Bluetooth LE to flash the sniffer .hex file into my dongle, install and configure the wireshard.
When I start the...
I am trying to install using VS code, using the video
https://www.google.com/search?q=install+nordic+visual+sydio+code&oq=install+nordic+visual+sydio+code+&aqs=chrome..69i57...
Hi everyone, i am new at this platform.
In my project, i need to take gps data from uart and send the data over zigbee with nrf52833. I haven't found any example and don...
Hi All, trying to find a cause of this problem, we have two devices, one is acting as peripheral and one as master.
Peripheral: ( nRF52832, s132 v7.0.1) a remote wireless...
I am trying to make a build with a slightly modified copy of the Zephyr button example on a nrf9160 board with a upgradable bootloader.
The following command can build our...
I seem to get error 4 on nrf_sdh_ble_enable when building and running the application in release mode.
Everything works perfectly when building in debug mode and I've checked...
Dear Ladies and Gentleman
Regarding the Bluetooth SIG Qualification the BQC needs a QDID for the Softdevice Controller Subsystem ( from table 2 of the compatibility matrix...
when i debug samples in Zephyr, i can see log through UART when i use "printk" function.
but i find there has "BT_DBG" and "BT_WARN" in code. so what's its using? and where...
i am receiving some packets so i need to send that packet to central device(mobile) if i send 20-20bytes it successfully sending the data to central device(mobile) if its...
