Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
I need to be accurate to five decimal places.
Use nrf52840 and ses.
Test code:
Execute d=atof(mm)/60.0 result 0.70693.It's right.
But e xecute d = 0.70693+22 result...
I am trying to use SAADC.
When viewing the contents of nrfx_saadc.c in SEGGER IDE all the code is greyed-out.
I verified it is enabled in sdk_config.h:
// <e> NRFX_SAADC_ENABLED...
Hi everyone,
I am currently attending the nRF Connect Fundamental Course.
As you can see from the picture below (taken from the Course material), there must be the chance...
Hello DevZone,
I was tinkering around with the speed of the TWIM0 module in the nRF52832.
I have a cheap USB logic analyzer to help me display the waveforms and I made...
Hi,
I am using NRF52832 development board , to which i have interfaced LIS3DSH accelerometer sensor(3.3V i2c)
when i configure it for 1600 sampling rate and all the...
Hello,
I am using nRF Connect for Desktop v3.12.0 with Programmer v3.0.4 on Mac. When I program mfw_nrf9160_1.3.2.zip on the nRF9160 dev kit, it works, but when I try on...
Hello! Very quick question. The available Zigbee and ZBOSS NRF documentation repeatedly to code examples that I am unable to find. The only examples I have are at nrf/samples...
I've previously successfully done interval advertisements using a SoftDevice with Nordic's previous (non-Zephyr) sdk, but I'm having issues replicating it on Zephyr.
Our...
Hi, I am using the nRF52840 with the softdevice s140 6.1.1 with the SDK 15.3 with FreeRTOS. Sometimes after collecting data for a around a day the device sometimes crashes...
Hi,
It has been a while since I looked up on different resources to get SPI slave transaction example and I finally found on the `nrf / samples / tfm / tfm_secure_peripheral...
Hello,
I have three questions regarding FEM.
#1 According to the following URL, FEM function is supported only for nRF52 series.
Would the FEM function be available...
Hi We are working on a new product that includes NFC, When we measure the voltage level we do not reach more than 600mv. The matching was done by capacitors: using a 2uH antenna...
Dear all,
I could happily flash my firmware to my nrf52840 upon pressing reset button. When pressing the reset button the diode on the board started to beat red and via...
Dear Mate,
i need brief explanation about below mcu bootloader like 1. starting bootloader how this starting bootloader works and where from it prints starting bootloader...
