Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi
I have noticed that when I configure any GPIO with "NRF_GPIO_PIN_PULLUP" option, the CPU current is raised by approximatly 200 uA. (It doesn't matter if the GPIO is...
Hello, I have managed to get two NRF5340s linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to test again. And then I also need...
Hi,
I need to enable the ADC read and GPIO pin toggling to happen simultaneously at high precision, without using the MCU resources, approximately 15 us interval. After...
We have a device that is using the nrf_drv_csense module to measure a capacitive touch via the event_handler passed to nrf_drv_csense_init(). Unfortunately, due to various...
The latest versions of MbedTLS seem to have some level of support for TLS 1.3 that the nRF Connect library's MbedTLS version lacks. How can I use a newer version of MbedTLS...
Hello,
I am trying to use Eigen matrix library in a project on the nrf52832.
I was able to compile a very simple example however I get a mem_manage_fault while debugging...
I am trying to connect a low power camera Himax HM0360 to nRF52840 dk. In the camera device specification, it is mentioned that it provides I2C serial interface and full speed...
Hi, I'm just experimenting with my nRF9160 DK and have run into some questions regarding the default asset_tracker_v2 program and how some of it works. I have read the documentation...
Hi!
Basically, what it says in the title.
Datasheet mentions that for 2Mbps mode (enhanced shock burst) spacing should be 2Mhz or more.
Does that mean that number of...
Hello everyone,
I used nRF24L01 and Arduino to jamming 3 channel advertising BLE ( https://github.com/lws803/BLE-jammer ) and my Gateway can't receive message from my door...
I am trying to develop an environment based on the prx ESB sample and add nrfx_timer.h dependencies. This is not necessarily a question specific to this setup but a more general...
Hi,
I am using SDK 17 version. The file name is ble_app_uart_pca10040 . I send to data from nRF Connect app to nRF52 DK and this data reach correctly to nRF52. But i didn...
Hi,
Now I have some custom data that I want to save in flash to ensure data not lost when power off. What should I do?
Platform: Windows 10
NCS version: 1.9.1
Boards...
