Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I use 9600 bsp of UART to communicate sensor data. I would like to add 115200 uart for wifi.
To use two uarts at the same time, what configuration should I do and...
I'm currently developping an application based on the Zephyr OS with its BLE protocol stack using the nRF52805 SoC. Due to security specifications, some cryptographical features...
In sdk 16 release notes i have read 52810 chips are supported for gazell secure libraries. But when i make the project port changes as described in "developing for 52810"...
Any recommendation for a filesystem for nand flash?
My application uses zephyr on nrf85240 with a 128MB nand flash.
It samples sensors and streams their data to the flash...
dear nordic team,
I was working on nrf52840 with nrf5sdk v 17.0.1 and sd v7.3 .Im using mergehex tool to combine bootloader+softdevice + App to download it to flash(using...
Hi Everyone.
IDE : Vs Code
SDK : nrfConnect SDK
I have tried to connect peripheral device based on address. User gives input , address of ble device and based on that...
Hi, I am trying to provision device using nRF mesh application. It discovers device and when i try to connect, it gives error device disconnected.
I tried this thing on...
Hi everyone, in special, Nordic; I'm facing a problem with the last two versions of the NRF CONNECT for Desktop (3.9.2/3) & the BitDefender Antivirus... I can download & install...
Hi everyone
I'm trying to generate the .hex file for examples like Tx and Rx or for my project but I'm not able to do that, please can anyone suggest me how can i do that...
I had been able to program my custom nRF52840 just fine until I wanted to change partitions. I erased everything and now am unable to communicate with the board at all. I...
https://github.com/NordicSemiconductor/pc-ble-driver-py/issues/210#issue-1089773469
I'm trying to build the project from sources. -using windows 10, python 3.8 -installed...
Port the radio_test sample to the Coprocessor sample to test the radio_test function error
How do I merge the two examples
I was hoping you could help me out
many...
Dear Sir.
We are using software based on mqtt simple project .
We added a 1 hz timer, Every 1 hz we toggle a led on and off.
Sometime the led is stuck on " on "...
Hi,
I'm trying to broadcast my BLE on my custom-made NRF51822 custom board.
My code was intended to run on Nrf51422, and it runs correctly on my PCA10028 DK with NRF514...
