Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello Trouble you again I can receive the data in the test now! But only the first few bytes can be received!
#define PACKET_BASE_ADDRESS_LENGTH (4UL) //!< Packet base address...
Can the nRF52840 dongle be used to sniff/record BLE communications even if the recorded packets cannot be decrypted, or can it only record packets when decryption is possible...
Hi all,
I got thread cli working and now I tried to set up a thread network.
I built the sample for the nrf5340PDK with overlay-minimal-multiprotocol.conf and overlay...
I currently trying to get my DK connected to nRF Cloud, I am based out of Western US and I have already provisioned my SIM card. I followed the documentation instructions...
In my program, there are different sections like each section does a different task and I am trying to use a different clock frequency for each section. So, I want to know...
Hello, I want to develop applications for my Mac and for iOS + Android smartphone. First I created a simple Mac gatt server with apples CoreBluetooth API which has one service...
Uart is initialized in non blocking mode but i need to use blocking transfer in a spacial case: is there any function available for this.
I can not reinitialize nrf_dvr_init...
Hi,
I have an issue when I want to read an attribute from a toll to my nrf52840 device.
For exemple attribut 0 of cluster basic, if I forge a general read request for...
Hi,
I am in the process of porting an application from an nrf52 to an nrf51 due to availability issues. One problem I run into is that bluetooth events are handled in...
The board connected to the PC for the first time, but after I mistakenly loaded the Bluetooth low energy sample instead, the Power profile on software nrf connected for desktop...
nrf51822's SWDIO/nReset pin is controled by a MCU GPIO output, a 1k resistor is in series. SWDCLK is connected to a pull-down resistor. And sometime (very rare) nrf51822 can...
Hi,
I am using nRF9160 multi cell location code on nRF9160-DK PCA10090 version 0.15.0.
Modem FW has been updated to the latest 1.3.1 binary.
I am using LTE-M with AT&T...
Hello there,
Recently I have added and been testing DFU into my existing application. I have conducted a few DFU updates and have noticed a semi-reoccurring issue. I use...
I currently have a working project with ethernet shield ( ENC28J60 ).
I use the driver from NCS 1.5.1.
I want to know how to enable logging?
I found some posts on this...
