Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi, I got my border router working fine, but I do not understand its use. How can I connect (which kind of protocol?) with the nrf5340 from my laptop to send turn on a led...
Hello
We check the current in system off in PCA10059 board. and use the ble_app_template application.
If set the VDD 3.3V, after the system off, measure the current is...
Hi Team,
I want to connect power pins on the nrf52840 chip in the schematic.
I find there several VDD pins, how can I select and connect them?
Best,
Gaosheng
Hello,
we are currently developing a customer product based on the nRF9160 SIP.
The requirement is to send the battery voltage periodically over the CoAP protocol (PUT...
Greetings , I have implemented an application with freertos (sdk 15.3) which goes into low power and wakes up on two irqs (rtc and button). When the button irq arrive turns...
We would like to use nRF9160 has MODEM only feature, such that MCU in our product can talk to nRF9160 via UART interface.
We have found an sample application [Serial LTE...
Hi
I am trying to setup a raspberry pi 4 for flashing nrf devices. But Nrfjprog doesn't seem to work.
I am using a Raspberry Pi 4 with 2021-05-07-raspios-buster-armhf...
Hi,
I noticed that the nRF9160s I2C low level logic voltage is quite high. With a 2kR resistor at 3.3V it's already more than 200mV. Because this is quite high and will...
Hello all,
I am using the BLE app UART code. I m trying to connect one plus through BLE connection. but nordic devkit BLE is not visible.
I am using the default configuration...
Sorry but I find the documentation useless. I don't even know where to start. It could be I have not found the correct documentation which is not surprising.
The best I...
Hi
I've built a USB HCI fimrware based on the sample from the nRF Connect SDK for the nRF52840DK.
See also: (+) HCI USB based on nRF Connect SDK 1.7.0 failed to update...
The SDK version of the program I developed with SES is v1.5.0. Now change the development environment to vscode and import the program into vscode through "add an existing...
Hi,
Is it possible to generate a passkey before initiating the pairing process?
The peripheral in my system does not have a display or input, so I'm looking for a way...
