Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
So I came across an issue while working on developing an app that can update firmware OTA. I was using Nordic Semi - android DFU Library
implementation 'no.nordicsemi.android...
hi，
1.Now I am using Wireshark to capture nrF52840 DK ZigBee packets. I have configured the environment according to the guide. In wireshark, "nRF Sniffer for 802.15.4"...
hi，
we are using52833 QFN40 to test carrier,but the program will loop at as the picture bellow,while it runs well in 52833 QQFN73 in another board, why? Coutl you help me...
Hello,
Our modem consumes a lot of current when we use a simcard from a provider 1 (a MNO), much more that when we use a simcard from another provider 2 (a roaming service...
Hi,
with a custom hardware, I'm using a NRF9160 with a ESP8266 chip over uart with following prj.conf and board overlay:
I was trying to open a socket (that uses the...
Hi
The chip used is nrf52832, the SDK version is a peripheral device v13, and the central device uses v16.
The referenced example is ble_app_multirole_lesc and has been...
Background: SDK 16.0.0, SoftDevice 7.0.1, 1 ble_central connected 6 ble_peripheral, Send an instruction to 6 ble_peripherals every 50 milliseconds, at the same time, the ble_peripheral...
We need fast response from peripheral to central. That means we need a fast connection interval. We are using less than 100mS. But that results in an unacceptable battery...
Hi I have a question regarding USB port on the nrf52840 device When connecting a new device to computer is it possible to tell PC to assigne the same COM port number as last...
Hello, this is my first post in here. I'm trying to read the TX_POWER information of my beacons. I'm able to read this info using the nRFConnect app on my phone no problem...
Hi,
If I want to write a driver to control the communication process on nrf52840, the SDK is based on BLE mesh5.0.
How can I do it? do you have any examples?
Best...
Thank you ahead of time for any help that the community can provide. These forums have taught me a lot over the past few weeks. In my project, I am noticing 20x higher sleep...
I'm unable to get SPI to work on my nRF5340DK board. I can see activity on MOSI and SCK pins, but not on CS. The pin is not even initialized and is floating.
My overlay...
