Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I am going through Lesson 9 of the nRF Connect SDK Intermediate course to understand how DFU and FOTA work in the SDK. I am using toolchain and SDK v3.1.0, and nRF Connect...
Testing a new nRF9151 device using a project derived from the Nordic "HTTPS client" sample project. We are experiencing a "Modem has crashed" event intermittently when running...
Hi，
Background Information:
Our product, BLE near-infrared device , is undergoing CRA (Cyber Resilience Act) compliance assessment—specifically for the EU RED Cybersecurity...
This seems like a silly issue, but I cannot get the UART output from the nRF9151 DK. Attached is a project that outputs via both LOG and printk() to a Segger RTT viewer without...
Hello,
I am working on a simple Bluetooth Mesh application for light control.
I started from the provided samples: - github.com/.../light - github.com/.../light_switch...
I am trying to program an external board using the development kid following the instructions HERE .
I am using the debug out P20.
I have tried supplying the board frm...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
i built a small breakout board for npm1300 (QEAAD0 2516AA) to experiment with it. the twi pins are wired to the i2c ports of a raspberry pi 4 to control it, and i have attached...
I do measure different values for source and ampere mode. On the nRF52 DK. Source Mode: disconnect SB9, Power Switch is off. Vout from PPK2 connected to nRF current measurement...
Hello,
We are using NRF5340 in our product and running automated hardware testing. As part of this process, we need to program the chip twice: once with a dedicated testing...
Hello,
I am using nrf52833-dk for making a ZigBee coordinator. I am using "network coordinator" sample code.
The project is making a ZigBee connection between "nrf52833...
My error message is that it works on a computer, but it doesn't work on the company computer. I'm not sure if it's the encryption software on the company computer, but I don...
I have a 5 year old design using a nrf52832 on a MDBT42Q module. The BLE option was placed on the PCB in 2020 and has been unoccupied since going into production. My customer...
Hello,
I am trying to build the sample/sensor/lps22hh project on nRF52840 DK and STEVAL-MKI220V1, but receive errors in build.
I have added an overlay file as in boards...
Hello, I need support regarding putting my device to low power mode (sleep) and waking up with a timer or GPIO input. I’m working on an application using the nRF9151 DK, with...
