Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
Toolchain manager is failing to download SDKs.
I am using:
Windows 10 PC
3.7.0v nRF Connect Desktop application
0.9.3v Toolchain manager.
Downloading sometimes...
Where is the provisioning configuration data getting stored ?
1. EEPROM
2. Any other non volatile memory
Is it getting stored in external chip to nrf52833 or inside...
Hello there!
I'm quite new to the topic and just tried to dig into it a bit, so I'm sorry if I didn't get all things yet about the nRF5280 Dongle :) .
Right now, I'm following...
Hi all,
Using the thread CLI example (on a PCA10056 board) as a starting point I would like nodes to connect automatically to a thread mesh when booting. I then want to...
I use the following example source code to test NFC pairing.
Example source code for NFC: nRF5_SDK_17.0.2_d674dde\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\experimental...
Hi
thank you very much for your paying attention.
Yes the peripherial_uart sample seems to be a good choice for my project. But Uart 0 pins didn't come out on GPIO connector...
Hi,
We are trying to create a network using 20 movesense sensors and BWG840 Fanstel gateway acting as the central. The gateway is running a modified ble app uart multilink...
I'm a beginner in BLE applications, and I'm having trouble with connecting nRF toolbox application
I wanted to use UART function provided in nRF toolbox.
But, an e rror...
Hi,
I wish to run an existing project in Segger embedded studio for its debug capabilities (Currently the project runs in VS code).
I'm using the nrf52832, running a bare...
I'm trying to add the unity test integration to our project, but failing to build, since the project has a dependency on nrf_oberon
For the sake of completeness, the project...
I'm having trouble connecting Thingy:91 to cloud.
I've installed both the modem and HEX image in the board successfully.
I've added the SIM card successfully to the...
I've had intermittent issues with the nrf9160 modem using mfw 1.3.0 with an iBASIS SIM getting stuck in "searching" state when first powering on. The symptoms are similar...
I am using a nrf_drv_twi_tx() and nrf_drv_twi_rx() for a simple I2C transaction but I'm noticing a strange behavior.
If I don't use APP_ERROR_CHECK(err_code); right after...
Hi,
We are developing a flutter mobile app, for Actility/Abeeway (chips from Avnet Silica) using flutter pluggin that relies on the Android SDK. In some situations (after...
