Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Dear friends,
I flashed a mesh serial example and fetched the Composition Datacomposition data by composition_data_get(), as below code:
I wonder the meaning about the...
I have implemented nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_beacon\pca10040\s132\arm5_no_packs code for iBEACON.
I am able to run it and able to see the advertised...
Hello,
I was using the send example which is located in C:\v1.5.1\zephyr\samples\drivers\lora and trying to send a message to an Arduino LoRa gateway.
However, I found...
Hello everyone,
I am stuck at a problem that I cannot resolve myself but I see that other people in the forum don't experience such a behaviour of their nrf52832s.
I want...
Hello,
I've been using SES for ARM (Nordic Edition) V4.16 (64-bit). I am working with nRF9160 sample code. While attempting to explore the code, when I right click on...
The program flow of the slave is to sample the analog signal source through the saadc and then send it to the host through the nus. When debugging on nrf52dk, configure the...
Hi,
In my main function, I just call a acceleration_read function to get data from the accelerometer sensor and call a NRF_LOG_INFO function.
But there're something wrong...
Hi,
I try sdk 17.02 nRF52840 usb audio demo,I want to achieve 48KHz stereo music play by a I2S DAC.
I finished adding DAC for I2S to play the sound data of USB Audio...
I am declaring the variable in one of the hardware drivers files that are provided by the nordic semiconductor. The variable is not static. The variable inside the function...
Are there any other QFN package baluns that we can use for NRF51822?
One suggested from STM is BGA, and I wanted to see if there are any recommended QFN baluns that we can...
Hi Nordic,
I have an NRF52805 board [ from Raytech] and I am implementing all my application using SDK v15.1.0.
As of now, I have implemented my application using the...
Hi,
We need to know rated output and gain of pcb antenna on nRF52 DK for a technical standards conformity certification.
Can you give us them and their evidence?
Thank...
I want to connect an LTE antenna to J1. However, the antenna has a normal male ufl connector - it appears not to fit.
Is an adaptor needed for this?
Thx for any suggestion...
Hi ,
my environment details:
nrf connect sdk
nrf5340 dk
segger embedded studio
I have seen I2C example code in below path
\v1.5.0\zephyr\samples\drivers\i2c_fujitsu_fram...
app_timer2.c from SDK v17.0.2 has a possible race condition in app_timer_start()
This calls the get_now() function which compares a "now" variable to a "m_stamp64" variable...
