As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Dear Nordic-Support,
have a question regarding nrfutil and the offline package generation, described here: https://docs.nordicsemi.com/bundle/nrfutil/page/guides/installing...
Hi,
I'm working on enabling dual-bank updates in our projects (we're using nRF5 SDK v15.3.0), and during this process I've stumbled onto some behavior that confused me a...
Dear nordic team,
I’d like to ask two main questions about nRFCloud.
1,Please tell me how to register devices on nRFCloud.
First, I’d like to register the following...
NCS 3.1.0 (and newer), nRF9160/51
Some applications using "at_host", maybe together with "at_cmd_custom", would benefit from a possible filter before passing the at-cmds...
nRF9151 - NCS 3.4.0
I like to use a library, which uses
CONFIG_PSA_CRYPTO=y CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_256=y
with NCS 3.2.4 successfully.
If I try to migrate...
Hello!
I'm working on a project that was primarily developed with NCS v2.9.0. The application (using an nRF5340) utilizes BLE mesh and is configured to use TinyCrypt for...
I am working with SDK v2.3.0 and a custom board with nRF9160
When I wanted to start my project again after some time, the build configuration had disappeared.
And creating...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
Hi,
Following the course Wifi Fundamenals with NCS v3.4.0. I have an error when building the exercise 2 of the lesson 4 (even with the solution one). I configured the board...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
NCS 3.4.0, sysbuild, with mcuboot enabled.
I want to use a simple custom "my.overlay" for both the app and mcuboot.
For the app it works with
-DEXTRA_DTC_OVERLAY_FILE...
I first noticed this when incorrect flags reported by mcumgr when performing network core update
When performing a network core update with CONFIG_SECURE_BOOT_APPCORE enabled...
Hello Nordic community,
using nrf5-sdk for nrf52840 SoC, I followed the uart example as below.
The uart tx and rx works fine BUT NOT THE HWFC
eg. When the CTS is set...
Hi Nordic Team,
Below are the configurations that I have done for the nRF21540 FEM.
.config file
#
# Multiprotocol service layer (MPSL)
#
# CONFIG_MPSL_FEM_ONLY is not...
I have a question regarding the solder balls on the WLCSP package of this device. Are they collapsing or non-collapsing? Can you also provide a definitive source for this...
