Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
I am running an nRF5 SDK BLE example ( Cycling Speed and Cadence Application ) on nRF52 DK as peripheral and connect to nRF connect mobile app as central, and I would...
I use the thingy 52 with the nrf52832 and the SDK13. I want to scan every 30 seconds and receive packets from other thingy's but I can't find how to initialize my scanner...
I can only see the conf files and other yaml files when i open nrfconnectsdk sample in Segger embedded studio IDE.Where do we exactly write our application code?Application...
Hi, there~
Currently, I'm working on nRF52840 DK with BLE Secure DFU Bootloader .
I have done the dfu with nRF Connect APP successfully.
But I have a question about...
Hi
I got it PPK2 and tested.
PPK2 is very useful compare to previous version PPK.
I wanted to sampling time expanding to 10min.
But i see that 2min time sampling...
Hello,
I would like to save some keys securely using the Infineon OPTIGA Trust X chip. To do a quick test I bought the Infineon shield2Go with the OPTIGA chip that I connected...
Hi All
as title.
I am nRF52 DK PCA10040.
Chip select is nRF52832.
I measure out from wfe to Timer Interrupt time is 1.3us.
Is it correct? and How can I reduce the...
Hello,
I am working on a school project with my team that requires one master device and up to 30 slave devices which will be controlling LEDs. I was thinking the nRF52840...
When enabling BLE on nrf52840, we are using specific API to access flash erase and write commands. All is working fine 99% of the time in term of read / write / erase into...
Hi Sir We are scanning nearest BLE using NRF Scanner example using 1- NRF52840-DK and 2. BT840 . We are getting good RSSI value using 1 but very poor RSSI values when we are...
Hi,
I am using nrf52832 with s132 softdevice and SDK17. I want to disable bonding and pairing in ble_multirole code. I have tried disabling the SEC_PARAMS_MITM, SEC_PARAMS_IO_CAPABILITIES...
Dear Sir,
I am using SPIM , EasyDMA array list,with following flags
NRF_DRV_SPI_FLAG_NO_XFER_EVT_HANDLER , NRF_DRV_SPI_FLAG_RX_POSTINC , NRF_DRV_SPI_FLAG_HOLD_XFER&
...
Hi,
I am using my nrf52832 board with a MPC9808 sensor and I wanted to use the example code provided in zephyr/samples/sensor/mcp9808
Can you tell me with which pin of...
