Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I try to create an MQTT AGPS tracker.
I'm using a nrf9160dk with the 1.3.0v.
I use two threads, one for GPS (A-GPS) and one other to send value to MQTT (witch starts...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
To set the transmit power for advertisement, I am using sd_ble_gap_tx_power_set...
We are planing to use nrf52840 sdk in our project.we want to use mesh stack for that.
our product is sensor:
-deployed in oil field.
- send data 8 times a day.
-payload...
Hi,
I'm developing on nRF51422 board and I'm currently adding BLE security just work feature based on SDK12.3.0 using softdevice s130_2.0.1(nRF is used as BLE peripheral...
Hi
Past week (on a Windows 10 pc) I've installed the nrf connect sdk (nrfconnectsetup331ia32), and yesterday offered me an update (nrfconnectsetup340ia32); since I've not...
Hi, I encountered the problem of losing data in uart serial port when using ble_app_uart_pca10040_s132 example.
sdk 16.0.0, s132, 7.0.1, nrf52832,
APP_ADV_DURATION=0,...
I want to connect two nrf52840 device and raspberry pi. When connecting to a single device, it works fine. However, when connecting with two devices, an error occurs and stops...
Hello all,
I am interested in using the Secure Serial Bootloader to program my NRF52832 over UART from an external MCU. I am aware of the SDK example and creating DFU...
I have a system that will have multiple ways of doing DFU. BLE, as normal, UART under special circumstances, and a "no transport" way. In the latter I will have transported...
Hi guys,
I was working on my nRF5340 based custom board. From a certain point on the nRF5340 stopped to accept any command from J-Link (SWD link). For example, in response...
I Separate two projects ,SPM application and non-secure application.the spi driver can work in non-secure application,when I try to transplant the spi driver in SPM application...
Hi,
We are using nRF52840 in HV mode and VDD is configured for 1.8v. By mistake, we have connected VDDH to one of the GPIOs as input. What are the implications? How much...
Hi Team,
We are using nrf9160 DK, So we tested the lte_ble_gateway application where we can take the ble data to cloud acting 9160 as gateway. So we also want to perform...
Hi, I'm trying to get the gps driver to work, but the initialization requires getting a device binding. The Asset Tracker project does it like this:
device_get_binding(CONFIG_GPS_DEV_NAME...
<environment> - Windows10 - nrf v1.3.0 - modem v1.2.0 - DK 0.9.0
I get "CLOUD_EVT_ERROR" when using nrf_cloud_agps. There is an error saying "Connection was closed, possibly...
