hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
IMEI 352656100982084
I need your support to solve this matter urgently because we are developing a IOT solution to monitor several thousand motors - one Thingy 91 for each...
Hi Team,
We are using nRF9160 -DK (0.8.3), As per the document we followed the procedure from here . Loaded the respective application to the on board controller(nRF52840...
Hello
I try to use nrf24l01 in multiceiver mode for a domestic application
I made a simple set-up with 2 nrf24l. On the receiver i activated 4 pipes (0 to 3) with these...
Hi,
I have updated the modem to version 1.2, and connect sdk to 1.2, and now the SUPL library doesn't work? I'm using the GPS sample and it is getting stuck at "starting...
I have the mesh light switch on/off example running. What is the easiest way to test sending and receiving data from a non-mesh device to the proxy node? I want to be able...
Hi All,
I have programmed my nrf52832 device with DFU bootloader,softdevice and buttonless app provided by SDK. I am using SDK16.
My device is getting recognized by nRFConnect...
Hi:
The nRF52840 VDD voltage supply range is 1.7~3.6V
So if we provide 3.3V to VDD, the voltage ripple spec. is still 1.7~3.6V?
Or other spec. that we need follow? ...
Hi,
I am evaluating a BLE beacon solution and the nRF52 seems attractive. If building a solution where an appliance I will develop will listen for a BLE beacon that I also...
Hello,
I am new on keil and nrf, I am trying to merge nrf52832 sdk15.0 ble_app_hrs example and this custom service
I want to send command from nrf connect app to my nrf52832...
Hello,
I am working on a BLE application for the Thingy91 which needs a lot of dynamic memory. In the Zephyr specification values of up to 16kB are supported. I tried to...
I am using zigbee light_control examples in nRF5_SDK_for_Thread_and_Zigbee_v4.0.0 for my zigbee projection.I want to know how the zigbee network build and which command will...
Hello, I have been using segger embedded studio v4.16 for almost one year using free license. today it says my evaluation period is expired. But they say it is for unlimited...
I have a setup with one transmitter and three receivers. The transmitter (nRF24L01+) sends a message to the receivers (nRF52832, using SDK v15.3.0) every 10 seconds. The receivers...
Setup: Segger Embedded Studio v3.52, nRF5_SDK_for_Thread_and_Zigbee_v4, nRF52840 Custom Board
Hello,
I based my code off of your Zigbee cli_agent_router example. In the...
