why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi DevZone! I'm migrating an app running on a Thingy91 from SDK 2.5.0 to 3.4.0. I will eventually try to adapt it to the newest Thingy91X. So far I managed to migrate the...
Hi all,
We're building a PoC of a simple BLE device with a following setup:
custom PCB with nrf54l15 rev2 and 32MHz oscillator
FreeRTOS + custom port
nrfx version...
We are observing an unexpected increase in current consumption when enabling the LED driver outputs of the nPM1304.
We configure the LED drivers to Host mode , which by...
Hello Nordic support,
We are preparing a build-only NCS2.9.0 environment on an Apple Silicon Mac, macOS26.5.1 (25F80), with commands run in a managed workspace execution...
Hi, i have downloaded the app nRF for desktop, but when i try to download an app inside it (such as Programmer or Direct Connect) i get notified with this error
i try...
1. ncs-3.2.4
I have a nRF54L15 IoT device advertising fine with ncs-3.2.4 (CONFIG_NEWLIB_LIBC=y), my FairPhone e/OS and my Samsung Android (using nrfConnect App or Serial...
Hi,
Our project has chosen nPM1300 as the PMIC, and our project's battery is only 28 mAh. When we tested the battery configuration file using the nPM PowerUP app, we found...
Hi Nordic team,
I am following up on a previous thread ( nRF54L15 sQSPI support for SPI NAND in NCS v3.3.1 ) where it was confirmed that NAND flash was not supported in...
The nRF91 series of modem firmware are distributed with FOTA-TEST diffs to allow for validation of FOTA integrations. Will the nRF93M1 firmware images be distributed with...
NCS SDK 3.4.0 NRF54LM20DK
The nRF54LM20A data sheet warns against using the same RAM subordinate by more than one bus manager. From section 4.2.1,
Avoid situations where...
Hi,
We are using the nRF5340 and a Pixel phone for the nRF OTA update. We observed that the Pixel phone application disconnects after updating the connection parameters...
Hi Nordic Team,
I've just received my nRF93M1 DK. Similar to this issue, I am unable to get my DK connected using the PPP shell sample.
Hardware: PCA10232 v0.4.0 Modem...
