hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hello,
I want to make a PWM signal that fires an interrupt at the end of the PWM period. I want to use two CC registers - one for the pulse width and one for the period...
Hi,
we developed design with nRF52840, but we have issues.
Propably we have solution for this issues, but we need test it and we need default hex file in nRF52840 for...
As it stands there is some confusion about licensing the DFU utility code in our systems we are concerned about licensing issues. We are compiling the python to an executable...
1.do I need to write a XX_client.c and XX_server.c myself ? is there a basic model that I can build on it ?
2.I need myself model to send a custom message, how to do that...
Experimental Dimming server example was working fine using SDK MESH3.0 in addition to SDK BT 15.2.
Following upgrade of the SDKs to MESH3.1 and BT15.3, the experimental...
Hi,
Does "ble_app_uart" project can print debug message from "UART" interface? How can I do this job?
PS. My UART Port is at P0.18 (TX) and P0.19(RX).
Thank you, ...
After turning on the power,
I did not connect anything on the board.
but it is about 2.7 volts out of the pin (p0.04).
It was almost zero volts before,
but the output...
In my design the nRF52 is connected to an STM32 host MCU. I connected the UART for data communication and the SWD and RESET pins for programming.
The nRF52 needs to be programmed...
Development Software:
nRF5 SDK v15.2.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware:
nRF52840...
Hello ! I encountered a problem in sending and receiving data from one nrf51 card to another nrf52 card
i use this method in (ble_config.c) to send string data :
void...
Hi everyone,
I am developing a quick evaluation demo for a low-power sensor node which consists of the following steps:
- read a couple of GPIOs
- set advertising...
Hi, we are developing an application using USB with NRF52840. We want to connect to the PMID of our battery charger, which will have either USB voltage or battery voltage...
We are using nRF52832 on original PCB board.
We are trying ADC at single-end input, 10 bit resolution, reference voltage is internal 0.6, gain is 3.
We are using regulator...
I would like to update my advertising data on the fly but actually it doesn't work. Many many posts talk about this behaviour, but no working answers .
Before SDK15, we...
Hello there!
My project use comparator, timer capture and pwm to measure capacity of line.
The purpose is to encounter open circuit condition. So this does not require...
