Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello everyone, I am planning to use the nrf52840 with the Fingerprint module (https://www.amazon.in/dp/B07DL2DXJX/ref=cm_sw_r_wa_apa_i_Z.VlCbXSSYVRS ). The sensor interfaces...
I got a new nRF51-DK board. I was planning on using USB to program it.
On the board I see pca10028 sticker. What is this?
Also in the SDK I see pca10028, and other pca...
Im getting this error, but i thing this has to do with some python dependencies, Im getting errors with
pip3 install --user -r zephyr/scripts/requirements.txt and installing...
Hi, I have a defined MACRO which I initialised the values of ble_gap_adv_params_t in main.c. I will pass this to the function to start advertising. I used the example (ble_app_blinky_pca10056_s140...
Currently in memory map nRF5 SDK 15.2 (which apparently is a base for Thread SDK) says for nrf52840:
Bootloader settings
0x000F F000 - 0x0010 0000 (4 kB)
MBR...
The nrfx api includes nrfx_gpiote_in_event_disable/enable , but I haven't found an equivalent of nrf_gpiote_int_is_enabled for a pin. I'm attempting to port an interrupt mutex...
nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_blinky
nrf_gpio_cfg_output(16); nrf_gpio_pin_set(16);
Set P0.16 to high level under the main part of...
There seems to be little documentation on TASKS_SUSPEND and TASKS_RESUME in the SPIM with Easy DMA section of the nRF52832 data sheet. My assumption is that TASKS_SUSPEND...
Hi All,
I am working on ISP1507 which is based on NRF52832. My IDE is Keil V5.26.2.0. I have had the following problem in the UART example (pca10040e) from SDK 15.0.0. I...
Hi,
I have modified the multilink example to work with NUS and connect to 2 peripherals, but I'm facing issues with data transmission. I suspect really low throughput...
Hi
I'm testing the range of a custom sensor (nRF52840) by monitoring the RSSI. I use two receivers (the custom sensor and a nRF840 DK) and monitor the received advertising...
Hello All,
I'm very new to Nordic.
For our product development we are using NRF52832 chip and nRF5_SDK_14.2.0_17b948a stack.
Battery powered device it's so is there...
Hi,
Previously, I have done a board and this board have completely no problem to debug in Segger embedded studio.
I have route a new board, this board is almost everything...
Hi,
During evaluation of both nRF52840 Dev Kit and Dongle somehow the Dev Kit bootloader was erased. We were able to flash MCU firmware, but now J-Link is not able to connect...
I am working on a derivative of the Glucose sensor code from nRF Toolbox. The sensor peripheral accumulates a number of readings. The central sends a command to the Record...
