Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello.
I'm trying to add encryption to the secure DFU bootloader. I'm using SDK v15. I know this topic has been discussed on this forum before. In particular I have found...
On NRF52840 DK, I don't have a softdevice installed. I want to do DFU with s140 softdevice only update. But it gives the following error:
raise NordicSemiException('Extended...
Hi,
I got a problem that doing the DFU through buttonless example, but successfully upgrade only in bootloader.
I used OPPO R9s (Android 6) with my personal cell phone...
which pin to use for TWI method communication, in board type 10040 nfr52832 model Taiyo Yuden EKSHJN
in file 10040 I have this definition of pins: what should i change...
Hello:
I have been at this problem for days now and not getting anywhere to a solution. My app is using a static passkey for encryption and does timeout after 30 seconds...
Hi,
I'm experimenting with incorporating " ATT_MTU Throughput" Example into our project.
I'm using nRF52832 as the peripheral and a SDK52 as the central.
The central...
Hi Everyone
I am trying to achieve the following objective
I want to upload the hex file of my application code which blinks leds after 1 second without using th SWD interface...
Hi,
I have my application working on NRF SDK11 on NRF52832 with softdevice 2.0. I am porting the application to SDK 14 and SD 5.0. I am facing APP_UART_COMMUNICATION_ERROR...
I posted the ble_app_uart example on the nrf51 dk board and tried searching for an app, but searching on Android, but not on iOS. Why? You have used nrf_toolbox in your app...
Dear all, my goal is to make a wireless HID device using nrf24/nrf5x products so, I've noticed the nRFReady Desktop solution that seems to implement the
RF connection nRF5x...
Hello,
I am trying to port the light switch server example form the nRFSDK for Mesh to IAR Embedded Workbench for ARM.
I am using
nrf SDK Version 15.0.0
SDK for Mesh...
Problem : bytes are lost during UART communication with the module, hardware flow control is enabled, at speed higher than 38400 baud/s, when softdevice enabled and test board...
Dear Nordic
I have facing some issues in RTC side. In my application RTC and BLE works same time . First installation and set time using function nrf_cal_set_time() works...
Hi all,
I want save and read flash in example light switch proxy server .
I add code part of provisioner example into proxy server example
This is my code ;
And...
