Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Hello,
I'm trying to flash my nrf52 DK but it's not detected by nrfgo studio.
here are the version of the softwares i'm using :
SDK : 14
JLink : 6.20g
Command...
Hello NorDev. community,
I have two sensors operating on nrf51822. I control them manually by mechanical switches at the moment.
I would like to change this sensor control...
hello everone
1、I tried the thingy52 sound demo ,but quality of the sound is bad, It is because the limit of the transfer speed？
2、I want transfer the sound by ble，how...
I would like to start off by saying I am not a very experienced programmer and I only have base knowledge of Java and Android Studio. Furthermore, I have no experience in...
when I run the secure bootloader example in nrf51422 development board, the code is working fine. I am able to load the packet through nrf toolbox app. But the same code when...
hello
i am using nrf 52840 board with sdk 13.
i use heart rate collector example to connect the 6 heart rate peripheral .
Modified the hrc_c example following this link...
I want to monitor NRF radio channell's RSSI to switch on "free" channel.
How to make it properly?
This is my code:
if(rx_q_flag == true){
err_code = esb_init(RX,...
I want to increase the MTU values to increase the throughput from my own service (currently based on NUS service) and to receive the data with pc-ble-driver-python with the...
I am using power_manage function to keep low power sleep mode. And I used below peripherals in code,
SPI master, SPI master is disabling when ever I am not using.
...
It appears to me that some of the saadc APIs (e.g. those found in nrf_drv_saadc.h in SDK 1.4.0) are missing in the nrf SDK for HomeKit.
Some hint where to find these functions...
How do you do
The attachment is a problem in the previous code, please help to debug it, thanks ble_app_uart_pwm.rar
E:\nordic\nRF5_SDK_12.2.0\examples\ble_peripheral\ble_app_uart_pwm...
Hello.
There is an executable file built by setting the address of the entry point (RO_Base) to 0x00000000 with Keil's linker setting.
I converted this executable file...
Hi,
I'm using nrf52840 with openThread. I like set the MCU in system on low power mode. RTC1 is used as application timer for wake up and start transmission periodicly. For...
Hello,
I could not find any related info, so I would like to ask few questions:
I have pca10028 board, using s110, sdk 6, ble_app_uart code. The board gets connected...
Hello all,
During current measurements of our product using nrf52832QFAAB0 I've noticed a high IDLE current of ~450uA. Trying to isolate the problem we programmed our board...
