There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx(the send length is fixed 10 bytes) ...
Dear nordic employee:
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Some questions during the development of a DF project using the nRF52833DK:
Will excessive serial output affect the performance of the microcontroller? For example,...
Hello,
On my custom board, after upgrading from NCS version 2.5.1 to 2.6.1, BLE stopped working.
I get immediately the following trace after calling bt_enable(NULL)
...
I'm migrating from ncs v2.3.0 to ncs 2.6.1 in order to have the ram retetion working with the mcu boot.
But after some modification on my board file using a nrf5340 I get...
I have a custom board file which is based on nrf9160, I want to use it using the west build command and later flash it. I tried the steps under this tutorial: Nordic academy...
Just upgraded to NRF v 2.6.0 (Mac OS; VS Code). Our code previous built and ran successfully on our custom board with v 2.5.0 of the SDK.
Now we get the following error...
Hi all,
I'm developing a project on top of nRF5340. Thus I created a custom board definition in my project area:
That is a direct copy of ncs/zephyr/boards/arm/nrf5340dk_nrf5340...
Hello,
we are trying to use the nRF9160 as a serial modem for a Raspberry Pi running on Debian.
The application is basically the nRF sample "nrf\samples\cellular\modem_shell...
Hi,
I'm trying to build the Serial LTE Modem in my nrf9160 SIP custom board to communicate the STM32 MCU with the nrf9160 using AT Commands via uart.
My physical connections...
Hi,
I created a custom service in accordance with NUS service. I am able to assign all handles, subscribe to notifications. But I am not able to read any data from the device...
Based on my understanding on SPI signal, CS/SS pin need to pull down to low when read/write and pull up high when the action is finished.
May I know if this feature has...
I'm currently working on a project that uses the MLX90640 IR sensor. By default, this device has an I2C address of 0x33, but it can be set up with one of 127 different I2C...
Sifting through previous posts about redirecting printf to uart by using retarget.c, I have found this will work on previous versions of segger (5.42). Has anyone gotten it...
I tried adding the following settings to prj.config
CONFIG_CHIP_OTA_REQUESTOR=n
CONFIG_CHIP_QSPI_NOR=n
I've also tried to modify the Devicetree to be the qspi part in...
Hello, I have a project sampling a ADC. It has a INT output signaling new data is ready to be read with max sampling rate of 125ksps. I am using the interrupt and then reading...
Hi community,
I'm making a custom board using the NRF52840-CKAA. I'm trying to make a Bluetooth application for this board but struggle to achieve it.
setup:
- Visual...