This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hi,
We are facing a strange behavior where the consumption we measure on the nRF5340 doesn't change according to supply voltage like it is supposed to do in DCDC mode. ...
Hello Nordic team,
I want to be able to save the log into a file and then read it in order to send it's content via HID.
I've managed to make the log back end FS work...
I have a nRF9151 based device, modem firmware version v2.0.3, with `CONFIG_LTE_LC_RAI_MODULE=y`, registered on LTE-M.
Using `NRF_RAI_LAST` is working, but I am seeing odd...
For the nRF9151-LACA-R, I cannot find the flatness parameter in its datasheet. Can you help confirm the flatness?
For the nRF54L15-CAAA, the datasheet shows A3 (0.03...
The MCP server requires authentication. To complete the setup, you'll need to: 1. Get an API key from Nordic Semiconductor / Kapa.ai 2. Reconfigure the server with the auth...
Hi All,
My leds on the custom board wont get recognized. Keep getting this error.
A bit of strack trace:
Device tree:
I think I am missing something...
Hi,
We're coming to the end of prototyping a project on the Thingy91X and are fine-tuning the power management. We have been able to implement a simple demo on the nrf9151dk...
Hi Support Team,
Our product is based on nrf5340 and ncs V2.5.2. I developed a Windows application(based on .NET8.0 and Windows SDK11) to provision and configure the system...
Hi, I'm struggling to setup an application on the nrf54l15dk to control the nrf9151dk SLM over UART.
I have done the Cellular IoT Course and successfully controlled the...
I'm trying out the GNSS sample for the nRF9161 DK. I am trying to enable minimal assistance, but I get an error message with error code 65536: *** Booting nRF Connect SDK...
Hi,
Can MCUboot be used as a second stage bootloader (an application from the Secure DFU Bootloader over Serial Link standpoint) to be DFU'ed to existing devices which now...
Is it possible for users to regenerate the nRF9160 GNSS factory almanac data from public sources?
https://github.com/nrfconnect/sdk-nrf/blob/main/samples/cellular/gnss...
Hel lo, I am us ing a custom nRF5 2832-based b oard that has no DCDC circu itry (LDO onl y). What happened in NCS v2 .5.1
After power-on, the system did not st art (e...
Hello,
I am trying to measure a fast, impulsive signal from an amplified analog microphone using an ADC pin on the nRF54L15-DK. When I read the same signal using a 12-bit...
Our production facility has some concerns about using the OTP parameters. Specifically, they are concerned about writing the wrong value and then needing to scrap the device...
