hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello,
I'm using the nRF52840 DK, SDK 17.1.0 and SoftDevice S140. My project is based on the Blinky peripheral example. The problem is the following:
Basically, turning...
I see a lot of threads about how you need to disable the UART while you're not using it because it has a couple of milliamps power consumption.
However, most of those threads...
Hello Team,
We are in process of designing our product with nRF52833. To secure our product and possible Firmware readouts, we are planning to use the APPROTECT feature...
So, I'm working on a project with two RGB LEDs, that's going to be powered by a coin cell. The device is going to spend most of it's time asleep, only waking up for a minute...
Hello - The nRF Connect for VS Code extensions updated today and it appears to have broken then nRF Terminal connection monitoring.
Old Behavior
Connect to device...
Hi,
I have a nRF52840-DK which comes with an o n-board SEGGER J-Link debugger/programmer to use with the internal microcontroller or an external one.
Also, I bought a...
Hello Sir/Madam,
I'm using Nrf52833 for ble_uart + saadc but this device given only 2 meter distance range .I want to increase that distance range.
How to increase distance...
Hi
I want to communicate with nRF52BK (nRF52832) board via its UART.
Eventual goal: Get Android device, acting as USB host, to connect with nRF52DK board's UART Short...
Hi.
I'm trying to run the http client sample for nrf9160 using nRF Connect SDK, but when I flash the board it gives this output:
Waiting for network.. Failed to connect...
We are seeing FOTA fail when updating from SLM using NCS 1.9.1 to SLM using NCS 2.0.0.
In summary, it appears that when NCS 2.0.0 image boots up, it never confirms and is...
I have a question about BD_ADDR.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) device: EYSHJNZWZ (nRF52832)
1) Is it possible to change...
Maybe I am being too newbie but in our own modules that handle state I am surprised not to find one to use, the closest that I can think of is:
#define EACCES 13 /**<...
I Need to write into external flash (attached in the development kit mx25r64)in a development kit nrf5340dk. I am using the code https://github.com/nrfconnect/sdk-zephyr/tree...
Hi,
we are developing a device which should go to system off on receival of a command either via USB or BLE. If the device is connected via USB and is put into sleep it...
