Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I use nrf52833 Development board PCA10100 to do loss test as peripheral and speed is 1Mbps, tx power is MAX. It's loss rate is very high, when nrf52833 sends a packet...
Hi, I am trying to use the periodic advertising connection examples and get Hci errors: opcode 0x2036 status 0x01 Failed to create advertising set (err -5)
I am on NCS 2...
Hi:
I checked the zephyr.dts file, but I couldn't find the addresses for interrupt-controller(0x e000e100 ) , timer(0x e000e010) , and memory(0x20000000) in the nRF9160...
With nRF7002DK and TF-M (nrf7002dk_nrf5340_cpuapp_ns.conf) configuration, the sample project works for example.com:
*** Booting nRF Connect SDK v3.5.99-ncs1-1 *** HTTPS...
Unable to write to flash memory using direct memory access functions like sd_flash_page_erase & sd_flash_write (nrf52840 nrf SDK 17.1.0) Also attached application and bootloader...
Hello, I'm experiencing an issue with communication between the nRF52840 and nRF9160 on the Thingy platform using the connectivity bridge. I successfully established communication...
Support,
Due to the limitations described in the referenced previous ticket, I am unable to successfully discover a service and its characteristics because of a hard fault...
I am struggling with the same requirement as this ticket :
ie receive from a UARTE without knowing in advance how many rx bytes to expect. This is typical for exchanging...
I'm running the nrf5340_audio application on the nRF5340 Audio DK and have a UART wired to TP60 and TP61. As long as I have USB (onboard j-link) or my Segger j-link connected...
We used to specify BOARD and BOARD_ROOT at the cmake level, but so far attempts to do the same using sysbuild did not succeeded. Is it still possible or should we rely on...
Hello,
Is it possible to know what is the cause of this assert : app: ZBOSS assertion in file: 24, line: 1024, please.
It is not very clear by reading the assembly code...
Hello,
Is it possible to know what is the cause of this assert : app: ZBOSS assertion in file: 24, line: 1050, please.
It is not very clear by reading the assembly code...
Recently the source control icon (git extension) in the activity bar in vs code shows more than changes in code.
As can be seen here the icon adds up the changes in...
AWS IoT example not working with v2.6.1 SDK with nRF7002 DK but works fine with v2.5.2 SDK.
*** Booting nRF Connect SDK v3.5.99-ncs1-1 *** [00:00:00.249,725] <inf> aws_iot_sample...
Hello all,
I use nRF52840 for my custom board. I set P1.11 & P1.12 as UART_RX & UART_TX. But these two pins can not work.
Here is my nrf52840dk_nrf52840.overlay.
Here...