why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
I am trying to create an AOA link sending a CTE from an nrf52811 (BM833A module) and the receiver with an nrf52833 (bl653 module). Analyzing the CTE detection data, the first...
Hello guys,
I've a PCA10040 connected to my laptop.
It works fine with all the .hex BLE template example in the nordic SDK except with the UART example.
After download...
Hello,
I was using the usbd_ble_uart code for the nrf52840 dongle. When I connected the dongle to u-link 2 debugger and used keil uVision I was just doing my settings in...
NCS version：v1.5.1
board：nRF5340DK(0.11.0)
first，i use SES Embedded open radio_test project and choose nrf5340dk_nrf5340_cpunet ,and use [west flash --erase] download...
I am using nRF Connect SDK Tutorial - Part 1 | NCS v1.4.0.
I am using MacOS and nRF Connect SDK v1.6.1 .
a. The JlinkExe executes but JLinkRTTClientExe doesn't show any...
As noted in recent past cases, we have an issue with the state of the nRESET pin that is causing unwanted resets when connected/disconnected from external hardware (programmer...
I used NRF52840 Base on NRF SDK15.3 and freertos.
I have two task call nrf_crypto_aes_crypt a t the same time occasionally return NRF_ERROR_CRYPTO_BUSY. And also I add mutex...
Hi
I am developing with nrf52832 development board and sdk17. I'm trying to communicate with redpine rs9116w through spi but get some problems.
I have an other nrf52840...
Hi,
I'm a beginner at this, I'm a software developer so I've never worked with hardware but now I need to and I don't seem to be able to make it work.
I would need help...
Hi,
I have nRF9160 Power Measurement DK board, (PCA63511 Rev 1.1.0). And
nRF52 dev boards (nRF52840) (PCA10056)
I measured my program as: with nRFConnect version 3.2...
I have a project I have been working on for a touch switch using the nRF52840. I have been developing it using NRF Connect 1.6.0 and testing it on the nRF52840DK board. It...
I have some code handling the `BLE_EVT_USER_MEM_REQUEST` event. When I try and call `sd_ble_user_mem_reply` from within that handler, It is returning `NRF_ERROR_INVALID_STATE...
Hi,
My application has several characteristics that require read/write authorization. But for some peer I only want them to have access to some certain characteristics...
Hi,
I have a custom board based on the PCA10015 where im not getting any contact between the NRF9160 and the IBASIS SIM.
The SIM is in the correct way and i have the same...
