hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hi,
I'm using NRF52811 to evaluate the direction finding. I have successfully got the phase data, but I found a strange thing:
I did some processing on phase data for...
I am currently testing Optiga Trust X using an NRF52 DK. I am using armgcc as my toolchain.
The example provided by the nRF5 SDK v17.0.0 is a great starting point and I...
Hi,
I am using nrf52810 and a sample SAADC code from the examples folder provided by the manufacturer. I have connected a potentiometer for validating my output values....
A continuation from here: https://devzone.nordicsemi.com/f/nordic-q-a/64842/mesh-pa-lna-problems
If I want to only enable the PA/LNA chip for the mesh stack, but not for...
Dear Nordic Support,
Our product is based on nrf52840/s140 and we have difficulties connecting to it using Huawei P8 Lite while it is fine using other Android or iOS phones...
I have a compiled code and I want only to change the uart pins without compiling the code again
If it is possible to modify only the hex code, how can I find the UART pins...
I am trying to find where to submit bugs against the pc-ble-driver. There are two major bugs I have found
saved CCCDs (in a bonded connection) do not get restored when...
Hello, everyone
I use NRF52840 to configure TWI to operate the sensor, but I don’t understand it.
Can the hardware TWI of 52840 be mapped to any IO?
Or is there a fixed...
Hello!
NRF52832 is used as a central for connecting with phones as peripheral. NUS service is used. Lesc is used too.
SDK 17 SoftDevice S132 V7.0.1
On android phones...
when I use usb to transfer, i fine many datas are lost.Is it because the DMA size is too small?Where can i see the dma size?(In nrf52833/examples/peripheral/usb_cdc_acm )...
I am trying to connect a SPI device to the external connector pins on the nRF9160dk board. I believe I know the name of the SPI device and the pin connections from the device...
Hello
I'm trying to print out several sounds with one buzzer. To do that, I need to be able to change the frequency.
PWM was initialized and reset using code. An attempt...
OS: Linux Ubuntu 18.04
Compiler: Gnu ARM embedded
HW: 2 nrf52840dk boards
NRF SDK: 16.0.0
I am trying to send data using L2CAP CoC. I have looked at the ots example...
Hello,
I am trying to get familiar with the DeviceTree macros and started experimenting ...
So, in the light controller example main.c I replaced this macro
#define...
