hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I am using 2 development kits 52840-DK.
I run the examples projects transmitter ( pca1056 ) and receiver. It works,
In an attempt to get longer range I increased...
Hi Nordic,
I had built a BLE custom service which has two characteristics and now I'm merging this with light-switch example, but while building it i got a problem which...
Dear All,
I'm pretty sure this has been asked many times but I don't know the right keywords to search for.
Alright, on our custom board we have a PMIC with regulated...
I try to start working with the nRF9160-DK. I gone trough all steps of the Getting Started Assistent from nRF Connect SDK. But i have a Problem with setting up a Project in...
Hi,
In my NRF52840 based application, I have a situation where the peripheral needs to pass 2K to central.
In order to speed up the xfer, I'm requesting a Connection Parameter...
Hi,
I am using nrf52832 and I want to build a device that can advertise iBeacon signals and can transmit data to another BLE device (central) simultaneously.
Can I do...
Hi,
I use example nRF5SDKforThreadandZigbeev3209fade31\examples\dfu\secure_bootloader\pca10056_uart to upgrade bootloader and coordinator application.
I try to upgarde...
Hello!
We are trying to get low average current consumption on the nRF9160 DK without success.
The floor current between modem active time is ~60uA, which is fine. But...
We've recently been testing the accuracy of the GPS on our devices. My basic method has been to trigger on GPS_TRIG_DATA_READY/GPS_CHAN_NMEA, and at each trigger fetch both...
I would like to advertise some sensor data (temperature, humidity, pressure, co2, voc and other) by BLE advertising packet without any connection. I know, I can put it data...
How much ram is my application + Zephyr + modem firmware using and how much is available in the nRF9160? I'm unable to find a memory map and anyway that wouldn't include dynamic...
Can we alter the eddystone tlm (telemetry) packet to send custom data . [This is not following the standard packet structure].
But I wanted to know how to alter the given...
I need a product that will allow me to connect a PC to a Bluetooth device through its Bluetooth connection. I will need to be able to send data bytes from my PC across the...
Hi everyone,
I am a beginner with Nordic SDK. I followed the " Getting Started Assistant" and then try to open asset_tracker project on step 4. During the opening I got...
