why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi, I'm using the nRF52840 Preview DK to get data from a digital microphone via a PDM interface. I'm using a clock frequency on 1.032 MHz to activate the microphone. The data...
Hi,
As discussed in this ticket we need a way to reduce the current consumption.
The LPN example doesn't solve this for us.
Our application is based on the light switch...
Hi, we have the latest Xcode installed on our new development Mac (up to date iOS too).
When we downloaded the iOS nRF toolbox from git hub today we get errors when compiling...
Hello Everyone,
I am looking for an Eddystone example. It should be used for an nrf52 with s132 SoftDevice (programming with nrf52 Prev Dev Kit).
Thanks for help
I'm struggling with how to properly identify an unprovisioned mesh device. Basically when i scan for unprovisioned devices from my iOS app, I'd like for only our devices to...
If I use sdk12.3 pca10040 S132
softdevice is s132_nrf52_3.0.0_softdevice.hex
How do I determine what version of Bluetooth it is?
In SDK or where the document has instructions...
Hi, I had download the nRF5_SDK_15.3.0_59ac345,but I couldn't find the softdevice S112 hex.(Nordic52\nRF52_SDK_Source\nRF5_SDK_15.3.0_59ac345\components\softdevice\s112\hex...
Hi ,
We have the following setup :
One nrf52840-dk acting as a multi-link central
One nrf52840-dk acting as a peripheral ( blinky app )
Both communicate well over...
I want to expand the Asset_Tracker example by adding the possibility to send data through UART2 to the controller and then to the nRF Cloud.
I am unable to find any document...
for 52840, customer want to have a part of flash, it can set write protect, to avoid illegal erase or destroy, they use this part of flash to run boot-loader, is it passable...
As far as I could see, only GGA NMEA sentences are enabled by default. I want to check if RMC sentences deliver positions faster, and in my prj.conf I do the following:
...
I got an nRF52 DK and I was unable to recognize the JLINK driver by connecting to my computer via USB. My SEGGER version is 6.44E and my own jlinkV9 is normal. How can I solve...
hi all ,
now , i need add create mqtt ble gateway .
it compiler failed follow message :
C:/temp/ncs/zephyr/drivers/serial/uart_nrfx_uarte.c:1272:9: error: 'DT_NORDIC_NRF_UARTE_UART_2_LABEL...
