I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello,
For BLE mesh light_switch example, the following statement is showing error.
In app_config.h
#define NRF_SDH_ENABLED 0
In sdk_config.h
#ifndef NRF_SDH_ENABLED...
Can someone tell me how to make device go to sleep and make it wakeup after a few hous using systick timer. I know how to create a timer but i wanna know which system call...
Hello. I have a breakout board (SMARTMP3 VS1053) and it has also a slot for memory card, so I connect the wires (SCK, MOSI, MISO and CS) to my nrf52832, but it can't see the...
What is the recommended way to protect characteristic value from modification while it is being read by a client?
I have a test application with 500-byte long characteristic...
Dear Team,
is there a tutorial on how to start from scratch a project for zephyr nrf91? With all configurations and flags...
That would be great!
Thanks & cheer
O...
Hello,
We're trying to create a custom bootloader from scratch and we're struggling with a weird behavior. This is for the nRF52840 and the bootloader doesn't use the softdevice...
The SDK version is 15.0.0, SD 132, single peripheral conection.
the configuration:
this is how i request the timeouts:
With the timeouts of about 50ms and less, the...
Hi guys,
I tried to modify "configs.c" or ".config", modified CONFIG_GPS_SIM_TRIGGER_TIMER_MSEC = from 2000 to 10000 .
But the device still sends GPS data every 2 seconds...
Hi there
I have a design in production using Gazell at 250kbs on a NRF51822
I would like to update the design using a nRF52840 but it doesn't support the data rate that...
Hi,
We are looking for a consultant to help us port our product's ( https://www.ncase.io ) firmware from Simblee to the Nordic nRF51822 or nRF52832. Experience with Nordic...
Dears:
I test the uart dfu by examples\dfu\secure_bootloader\pca10056_uart
After I enter command like below：
nrfutil dfu serial -pkg Sena_app_uart_s140.zip -p COM5 ...
My project is Obj-C , and “ pod 'iOSDFULibrary' ” in my Podfile.
It worked fine until I upgraded Xcode to 10.2. There are some errors(about 100) occurred during project...
Hi all
I am doing multiprotocal from sdk15.3 and I am trying to add nrf_gzp.c, nrf_gzp_host.c, and nrf_gzp_host_nrf5x.c in to the project
after compile successfully and...
I was wondering, is it possible to suspend/resume flash operation in nRF52840 (internal flash)? Like flash erase suspend, and also flash write suspend/resume?
Thank you...
Hi,
Might be a silly question,
but is there a gattc equivalent of the "BLE_GATTS_EVT_HVN_TX_COMPLETE", ie a similar/equivalent event that gets generated when a central...
