Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello everyone,
right now I have two BMD-340 Evaluation Kits which used nRF52840 module and I want to evaluate Bluetooth Long Range and Data Rate of this module. I used...
Hi
I saw a fail for RF-PHY/RCV/BV-29-C on nRF52840 DK.
But I also find it is a known issue as "Anomaly 172 Addendum".
In the nRF52840_Rev_1_Errata_v1.2.pdf, two workarounds...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
Hi
I have this code that works like a charm when the device is connected and I want it to leave the network.
But if the device is dead or disconnected and I want to remove...
Hi,
I know this is a license question and the default answer is "contact a lawyer if you don't understand the license". But this can hardly be the first time someone...
Hi,
I'm trying to connect nrf52840 to IOS 12.1.4 as a Braille display. Standard BLE HID is working well, but when I try to connect as a Braille Display ( Settings/General...
I am trying to connect and according to the spec sheet, there might be multiple pipestatusevents.
When I try to connect using different phones (with different Bluetooth...
Hi,
I'm using the light switch client example to test the Mesh App on iOS.
The PCA10040 board can be identified through Mesh App, but not be identified on our test board...
I am using nrf52810 chip without softdevice or bluetooth stack. I started to develop at November 2017 with Datasheet version v1.2. On 31. Januar 2019 Nordic released a newer...
Hello,
I have project for collecting temperature information from 15 pcs temperature sensor.
It is possible to create system with 16 pcs nRF52840.
one of them will be...
Hello,
I’m using two nrf52832 as servers sending 20 Byte data with 18 ms notification interval.
Notification Data:
[incremented uint8_t ] [19 byte data]
Client:...
Hi,
I'm working with the nrf/samples/nrf9160/at_client (@ tag v0.3.0) with a PCA10090 board.
I had a question about the response to the AT+CESQ command.
Specifically...
hi,
i am quite new with programming tools like the nordic thingy and i am currently trying to get some initial program running, i.e. the blinky example. i have a few questions...
