Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi,
I'm working with the nrf/samples/nrf9160/at_client (@ tag v0.3.0) with a PCA10090 board.
I had a question about the response to the AT+CESQ command.
Specifically...
hi,
i am quite new with programming tools like the nordic thingy and i am currently trying to get some initial program running, i.e. the blinky example. i have a few questions...
I am converting the simple_on_off vendor model to send a message on mesh 3.1.
the server implemented the simple_on_off model successfully. But but my client runs into 0...
Hi currently I am using the nrf_mesh_sdk_3.1 latest release light_switch Example both client and server one after successful compilation and load examples in DK boards when...
Hello,
I have updated secure_boot to allow UART3 to be used in the non_secure area. However, as soon as I try to initialize it in the non_secure area a hard failure occurs...
Hello! I took the example of "usbd_cdc_acm" and added a receive and transmit buffer. The data from the receive buffer is sent back. It turned out that the first byte is written...
Hi All.
I have a project where my peripheral (nRF52832) connects to my central (nRF52840), and then transmits 128 byte packets continuously one after the other. It works...
We are using the nRF9160 DK with the Asset tracker example, which is working in combination with the nRF Cloud.
Now we want to use our own AWS account in combination with...
hi all i am trying to read data from a sensor in burst mode i can"t able to read all datas from the register .I tried to read the data in both spi and spim(with easydma) ...
Hello,
So I'm using nrf52832 with sdk15.2 and I'm trying to connect a joystick to the adc pins and have the joystick to move the mouse instead of the buttons and having...
hi.........
i am tried to merge the blinky and timer sample program , i am getting this error , even i have included all files .h , .c files
nrfx_config.h: No such file...
Hi
I am using nrf51822 chip to develop my application & I need to put the hardware into sleep. In which all the gpios & other peripheral goes stop to save power.
SO, how...
Hi,
I want to change MAC address during advertising in nrf52810.
nrf52810 receives MAC address via uart from other MCU and set this MAC address. (type is BLE_GAP_ADDR_TYPE_PUBLIC...
We're building small robots/toys that work with each other.
Would it be possible to use the nfct on two devices with nRF52840 to communicate between each other?
Also...
Hello,
I’m sorry for asking again, but I could need some help again. This is a followup to devzone.nordicsemi.com/.../missing-endcrypt-event.
I’ve managed to receive...
