Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I have set up the Cloud Coap example in the Iot SDK using a nrf52 Dk. I have been successful in sending a serialized byte array from the nordic to my cloud server. I need...
I use nrf51822 sdk130 (central device) and nrf51822 sdk110(peripheral device). I want to get rssi value of the peripheral device using the central device without connection...
Hi Hung Bui,
I am working DFU now, all the thing's good for nFR52832, but in same way nFR52840 not work, I just wonder nFR52840 is ready for DFU?
Thanks.
JG
HI,
I want to turn off the broadcast timeout, but when I change the broadcast timeout macro to 0 when the program does not work，
Modify as follows：
#define APP_ADV_TIMEOUT_IN_SECONDS...
I'm attempting to use Peer Manager with my nRF52832 module as a peripheral with an Android 7.0 phone as the central device.
My program is a mix between the NUS example...
Dear Nordic,
I have built a board using nRF51422, and I've just manage to populate it and start it up.
I'm using a modified example (peripheral_lbs), and everything seems...
Hi, I have an Adafruit Feather52 board which is preloaded with a serial DFU bootloader and the S132 Softdevice, of which I also have the merged Hex file. I would just like...
Hi,
I am designing a custom PCB using the nRF51422 chip. I have a program that I developed on the nRF51-DK. The program reads the capacitance value of a proximity sensor...
Hi All,
i need some helps. I need a device that can connect with one phone only, so i have created a whitelist wih size of 1.
During the life of device the device can...
Hello, I'm pretty sure the new BLE 5 will come out soon and it will integrate the mesh. And if mesh needs to be done at a protocol level, it must be the softdevice.
So...
Hello iam using softdevice 110 and SDK 10.0.0, i have implimented dfu in my project, i want to update a region in EEPROM by calling pstorage_update() function before calling...
A while ago I asked this question devzone.nordicsemi.com/.../.
Yesterday I re-installed MDK 8.11 after a computer crash and I had IAR version 7.60.1 and version 8.11.2...
Hi,
I need to design a small nRF52 board On 24mm Dia 2-layer PCB, same like nRF51822 Bluetooth Smart Beacon Kit (nRF51822 Coin-Cell design). Please find the attached Schematics...
