Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Do anyone ever measured current consumption of ble_app_uart?
What is current when connected and uart idle, transmitting, receiving, and transmitting while receiving?
Please...
I tried changing the define below from 1 to 2, so I could have one handler for a button and a different handler for other sensors. But my problem is:
If I set it to...
Hello,
I've developed a circuit with Mikroelektronika's nRF T click module. This module uses nRF24L01P but as I see I cannot order it because it is obsolete.
Should...
We plan on use the ST BAL-NRF01D3 balun for a PCB with both an nRF51822 and a nRF51922 on the same PCB separated by about 4 inches.
Should we use the PCB antenna as on...
Hello.
I am very confused with memory layout of nrf51822 BLE examples using SoftDevice stack.
Some examples set IROM1 range from 0x0 to 0x3ffff. (ex, ble_app_advertiseing...
Hi,
I have a nRF51422-EK board (Rev. 1.0) that is bricked.
When connected the LD3 is on.
Jumpers are present on P8 and debugger.
Device manager (win7) assigns...
Hello,
I was puzzled by RM.
I notice POWER control register in peripheral(UART,SPI,TWI) module.
Please answer following questions about the relation between system...
I download the softdevice for PCA10001. And I want download another program, but it didn,t work. The problem I have attached here. As you known, I have push the button 'recover...
We plan on using the external 16 MHz and 32 KHz oscillator inputs to reduce BOM costs since our host micro uses a 16 MHz and 32kHz crystal and it can generate outputs. If...
Hi guy:
I have buy nrf51822 dk .Why I can not download nRF UART App for Android 4.3 at below page www.nordicsemi.com/.../nRF-UART-2.0-for-Android-4.3
Thx
I made code like to below for using 16Mhz system clock.
/* Start 16 MHz crystal oscillator */
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0; NRF_CLOCK->TASKS_HFCLKSTART = 1;
...
Hi guys,
I have designed a custom board with nrf51822. Data transfer seems OK, when I do it through Master Control Panel - I can write data to characteristics and I can...
Hello
I'm planning to use the nRF8001 SCC with an external microcontroller. So far we have purchased the nRF8001 sdk and the nRF6700 Started kid. My question is simple...
