Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
Hello,
I have some questions regarding S110:
Is it possible for the S110 softdevice to scan for broadcasts?
Is it possible to create a connectable broadcast...
Hi all,
I'm trying to implement two hex files into my processor, one application and one bootloader.
In nRFgo Studio I enabled 2048 bytes in the NUPP field to get a protected...
I've been working with writing and erasing flash. And somehow I can't flash softdevice 6.0 into the NRF51822 G0 chip with NRFGO. The error information poped up is "An error...
Hello,
For my application i need one central device collecting data from sensors. For central side i would choose for the nrf51822(s120), simply because it has high priority...
I know it was asked and I was searching but I didn't find a clear answer about that. I know that I can generate any random 128bit UUID for all my user services & characteristics...
Hello,
I am using nRF51422EvKit with Heart Rate Monitor example. Device is detected by PC (Windows 7) but in device manager appear "External Bluetooth device" with marking...
Hi,
We have a custom board with nrf51822 chipset, when i try to flash ble_app_proximity application through keil, it is giving advertisement, but i cannot able to connect...
I have a custom PCB and i have connected the MISO,MOSI,SCK,REQN and RDYN line from the nRF 8001 to Arduino. And uploaded your code of ble_uart_project.ino but nRF 8001 does...
Executing:
nrf_gpio_range_cfg_input(0, 39, NRF_GPIO_PIN_NOPULL);
I believe it will.
I know the range should end at 30 but I hit the wrong key when I coded it. So...
I have a characteristic that is 80bytes long which is sometimes read by the client using long read. I also want to send the complete attribute value when its state changes...
Hi guys,
i tried to find information about the differences in chip revision
nRF51822-QFAA-R7, NRF51822-QFAA-T and nRF51822-QFAA-G0 but i can't find the R7 or T type anywhere...
1.
Are there any other resources than RTC/WDT requiring 32kHz LFCLK, not listed in Table 28 of nRF51422 PS (i.e. Radio)?
2.
ANT stack requires LFCLK +-50ppm, so +-25ppm...
Hello,
I'm getting an exception while starting MasterEmulator Sample Programs. All indicated Dlls were copied along with .exe, windows ver is 7. the same error happens...
