I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi Team!
Does release 2.1 of the SDK address the issue raised in the below ticket with LWM2M implementation?
I have made the necessary changes to Asset Tracker v2 application...
I am looking at adding BLE to an existing design. The product uses an ARM micro, and currently has SPI and I2C available at daughterboard connectors. I am trying to understand...
Hello, guys.
I am using nRF Connect SDK, version 1.4.2 and nRF52840DK. I wonder what would be the way to print floating numbers during debug phase?
According to this thread...
Using the latest nRF_Connect_SDK
How can we set a udp/dtls socket, peer connect timeout for this call:
If there is no way to set a timeout for the call itself, is there...
Windows 10
NCS 2.0.0
We have run the Gazell samples successfully on the nRF52833 DKs. In these examples the CONFIG_GZLL_TX_STATISTICS is enabled (gzll_ack_payload_device...
Note: This might actually be a documentation issue more than a real problem because the build seems to work. But some clarification would still be appreciated.
We're developing...
I'm developing FOTA through LTE Modem which is made from QUECTEL(EC21KL)
On my custom board, nRF52832 is connected with EC21 LTE Modem via UART bus(TX : P0.16, RX : P0...
I am updating Nordic Thingy:91. I am following instructions on Nordic's DevZone web page: "Getting NB-IoT Demo running on Thingy:91
I have successfully updated modem using...
Hy
i am using a nrf5349 Dk board ,i am able to build and flash the board.
but when i am using this by building and flashing the board with hci_uart .in the linux system...
Hy ,
After i a buildng and flashing the hci_rpmsg as a cupapp . i flash the board
Then when i am checking the board with ubuntu laptop .i am not able to see the board...
Hi all!
I'm currently working on the UART on the nRF5340 board. The SDK describes three options: -polling API,
-interrupt-driven API,
-asynchronous API. With Polling and Asynchronous...
During development I noticed the following behavior:
If NRF_SDH_BLE_GAP_DATA_LENGTH=251 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE=185, on Android devices the connection procedure...
Hi
For some reasons my Windows 10 laptop reports two JLink CDC UART Ports when I connect one of my nRF52SDK boards.My plan is to use this board with nrf Sniffer / Wirshark...
