As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
with a custom hardware, I'm using a NRF9160 with a ESP8266 chip over uart with following prj.conf and board overlay:
I was trying to open a socket (that uses the...
Hi
The chip used is nrf52832, the SDK version is a peripheral device v13, and the central device uses v16.
The referenced example is ble_app_multirole_lesc and has been...
Background: SDK 16.0.0, SoftDevice 7.0.1, 1 ble_central connected 6 ble_peripheral, Send an instruction to 6 ble_peripherals every 50 milliseconds, at the same time, the ble_peripheral...
We need fast response from peripheral to central. That means we need a fast connection interval. We are using less than 100mS. But that results in an unacceptable battery...
Hi I have a question regarding USB port on the nrf52840 device When connecting a new device to computer is it possible to tell PC to assigne the same COM port number as last...
Hello, this is my first post in here. I'm trying to read the TX_POWER information of my beacons. I'm able to read this info using the nRFConnect app on my phone no problem...
Hi,
If I want to write a driver to control the communication process on nrf52840, the SDK is based on BLE mesh5.0.
How can I do it? do you have any examples?
Best...
Thank you ahead of time for any help that the community can provide. These forums have taught me a lot over the past few weeks. In my project, I am noticing 20x higher sleep...
I'm unable to get SPI to work on my nRF5340DK board. I can see activity on MOSI and SCK pins, but not on CS. The pin is not even initialized and is floating.
My overlay...
Hi,
During automatic assembly of the NRF52840-QIAA
We have found after Xray that we have air gaps surrounding ground pad vias - see attached images below.
I am...
I have a project that runs I2C to collect data from a pressure sensor and I have a different project that sends arrays of data over Bluetooth and they both work perfectly...
We are using RTC with external 32.768Khz clock to maintain and count a full date.
we found that we have a drift of time counting about 1 minute on every 10 nintues which...
I have the NRF52-DK, a 3-digit seven segment display, an RGB LED and a sensor. Using SES to try and get some basic code running.
I manage to open an nRF Connect SDK project...
