Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello All,
i my project there are 2 ble services now i want to add Flash read/write application i tried with fds as well as flash_write example from the SDK 15.3.0
i added...
Hello!
Apologies in advance for my english.
I already asked a similar question, here is the link to it
When trying to connect a PWM driver PCA9685, I ran into problems...
Hello.
We are using NRF52840, SDK 16.0.0 and SoftDevice S140 7.3.0 and are noticing irregular SoftDevice asserts that don't seem to be triggered by any one particular function...
Hello,
I am curious to see if it is possible to register a device through a web app using the nRF52840's NFC. The goal is to scan the NFC on the device, enter the personal...
Hello,
I'm working on a custom board with a nRF52833.
A small external battery is on the board, and when the power is off, 32.768khz of low power remains on the battery...
I'm running the SDK 17 radio test example on two nRF52840 DKs. My goal is to do a PER measurement in 802.15.4 -mode.
I configure the boards to use ieee802154_250Kbit mode...
Hi, I am using nrf52832 board. I was trying to disable the GPIOTE interrupt for a particular event (Event4) using INTENCLR register. My code was NRF_GPIOTE->INTENCLR = 1 ...
I am trying to get the nRF9160 DK power consumption down as much as possible to establish a baseline for development. After struggling to achieve the values claimed in the...
Hello,
I am using NCS v1.5.0 and an nRF9160 on a custom board, my application has a custom SPM and the secondary slot for the firmware image upgrade is stored on an external...
Hi,
I'm developing a peripheral sensor and central receiver as a complete set. So I wish the peripheral is only visible(or connectable) to its central device.
I know the...
Hi there!
I wanted to do a little side project that's something completely different than BLE Mesh (which I do for work). I decided Zigbee would be fun. Even more so because...
Hi,
I have an nRF52840 DevKit and dongle and am using SDK for mesh v.5 with SDK 17.0.2.
I want to update the firmware in a mesh network and am working on the mesh DFU...
I am using nRF52832 S132 V7.2.0. I am using ble_app_hrs_c example.
I only set nrf_ble_scan_filters_enable(&s_scan, NRF_BLE_SCAN_NAME_FILTER, true) to scan and match successfully...
Hi,
I am interfacing the Peripheral_hids_keyboard + peripheral_uart code
I code can print all the log info data printk and printf data in uart console
I want to separate...
