hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
We are using nrf52840 USB dongle to get PIR sensor readings and send measurements over the Bluetooth Mesh Schematics are following: We increased power for peripherals to 3...
Hi:
When I use nRF51822's 2.4G Radio(not BLE),I want to improve anti-interference level,Make sure that all my pairs of host and device can communicate normally.
Thank...
Hi
Looking at the AGPS sample code, it seems GPS/LTE is turned on and off using AT commands (AT+CFUN=x, x in {20, 21, 31}).
Do you recommend NOT using PSM when using AGPS...
Hello,
I have several nrf52 Development Kits which will be used for creating a Bluetooth mesh network. They sport the NRF52832 SoC.
Do they have, or will ever have, support...
Hello
*Environment
- LG V30 (Android 9)
- nRF52832, 15.3.0 SDK, S132
- nRF5340 ( I can't find SDK version)
I have some issue.
LG V30 Mobile can't reconnect...
Hi,
I am using nRF52840 USB dongle and DFU trigger library to update firmware without push any button.
The Python 2.7.x is working fine for DFU trigger into the DFU mode...
Hi!
I am developing a iot solution and I wanna send sensors data to broker by MQTT publisher. In my code already has the W5100 development and now I want to connect my device...
Hello,
I would like to create a new box in the nRF cloud for recording additional data. I know these boxes allow exporting the recorded data into a CSV file, which is ultimately...
Hi,
I have the below queries regarding the power consumption and memory
1) If my device is connected to the mobile phone and if it is scanning and the same it is advertising...
I'm trying to develop a code for the nrf52840 with a BLE link as Peripheral and Server (common configuration, but no SDK example). I start with a GATT server and changing...
Hi,
I try to use nrf51 dougle as a sniffer.
My nrf51 dongle not show up when connected to PC, when press the reset button, it only shows the boot-loader.
I try to find...
Hi everyone,
I want to measure the strength signal of BLE of my device. I need to do this measure without connecting/paring my device to any other, just during advertising...
Hello, Are there plans to include the nRF52833 reference design to the Eagle library on github ? In particular nRF52833 QDAA QFN40 (with the 201's).
There was a similar...
Hello,
I'm using the nrf52840 and SDKv16 to interface with an SD card. An SD card block is 512 bytes. I would like to do this:
1. Get the card ready for a write (use blocking...
