Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
I need to port a system from a STM32F407 MCU to the nrf52832.
The old system would continuously poll a SPI slave for 244 bytes of information and after receiving 60 valid...
Hi,
I am working on the ADC and trying to sense the battery level to measure it voltage.
And I have configure the ADC with normal conditions as present in example of SDK...
Hello
First things first, when I use the UART example located in:
\nRF5_SDK_15.2.0_9412b96\examples\peripheral\uart\pca10040\blank\ses
all works fine, the script compiles...
Hi,
I hope this is the correct place to ask beginner questions. I new to microcontrollers in general.
So first of all here is what I am using currently:
Software:
...
Hi,
I'm using Nrf52 with SDX 15.2.
The device is far for the host (smartphone), I would like to know if I can know the RSSI with the Smartphone? How can I control the...
Hello everyone!
I'm trying to implement a mqttsn client inside a microcontroller, and the nrf52840 should be used only as a way to communicate with other thread devices...
Hello!
My name is Tiago Morais. I've started to work with nrf52840 and now I'm having some problems with its CLI.
I'm trying to use the nrf52840 dk with openthread and...
Dear Nordic Team, Thanks for supporting.
Currently i am working with DFU for nRF52810 custom board. I am using SDK15.2.0. I followed these steps (//devzone.nordicsemi.com...
Hi all,
I'm following https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK/v3-0-0/md_doc_getting_started_dfu_quick_start and I'm using mesh SDK v3.0.0, I have a problem...
Hi all:
All of the example code is using GPIOTE to demonstrate how to handle GPIO interrupt.
However, it just can configured HiTOLow/LowToHi/Toggle.
If I want to trigger...
Works
Use nRF Connect v2.6.0 on Linux to erase, program softdevice.
Works
Use Keil to program application firmware
Does not work:
Use nRF Go studio to detect...
I need to implement a simple uart protocol. most messages are fixed length (8bytes) with some exceptions.
here what I do in pseudo code, I send 8bytes and expect 8bytes...
Hi
I am trying to port an SPI driver from a project for the NRF51822 to an NRF52832 and running into a problem reading more than two bytes. We are using SPI0 (not SPIM0...
Hello,
I'm using an NRF52 DK board.
I noticed that when I change P0.27 from the default (input / not connected to input buffer) to being an input pin connected to the...
Good evening,
I had a question in respect to the exact procedure needed to read a characteristic with read permissions. I have just discovered a service i would like to...
