why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
I'm trying to toggle GPIOs 32-35 but it can't be done. Other GPIOs though such as 15,21,30 I change successfully.
Here's my code:
I saw a solution regarding NFC...
Until lately, I have never used characteristics longer than the 20 Bytes and if the length of application data was longer, I would fragment it on the application layer.
...
Hi there,
I’m trying to port Thingy to Segger Embedded Studio. After reviewing some related blogs on devzone and github, I have imported the Keil project into SES. All files...
Hi,
I'm trying to use adxl335 accelerometer to detect motion.
I'm having trouble understanding what the output of the accelerometer means.
Obviously, it should tell...
On SDK 12.0.0, SDK 12.1.0 and SDK 12.2.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic...
On SDK 13.x.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic effort to find issues and...
The soc_evt_handler() function in nrf_drv_clock.c need to set m_clock_cb.hfclk_on = true.
When the softdevice is enabled and multiple modules request the HFCLK using nrf_drv_clock_hfclk_request...
I'm following your instructions for testing the Thread Secure DFU example , but I run into a message "Waiting for NCP to promote to a router ..." at step 6 and I don't o bserve...
I had used the examples\peripheral\blinky\pca10040\blank\arm5_no_packs Keil project from nRF-SDK v15.0.0 using Keil MDK v5.25.
EDIT: as described here: http://infocenter...
Hello,
I am currently implementing an OOK modulation with the nRF52 -DK and therefore I need to start the radio with a carrier on defined frequency. Obviously there is a...
Hello
My English is not very good and please point out if my problem description is not clear. I am building a central project that can connect two peripherals. The template...
Hello Nordic,
we are going to perform RF-PHY test for nRF52810 at DEKRA. Can you help us with IXIT filling? There is one answer available at devzone:
https://devzone.nordicsemi...
hi
i have written a service and added 3 characteristics .In master controll panel i am trying to discover services.i see these logs . Device gets disconnected while discovering...
Running the `examples/ble_app_uart` on below environments, in Nexus6 only, it causes that local name byte array will be broken.
* DK：nRF52 PCA10040 v0.9.0 * SDK：14.2.0 ...
Hello all,
I am working on a college project where i need to interface a SD card, an OLED display along with BLE support on nRF52DK, PCA10040, s132, SDK14.1, Segger embedded...
