Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I followed the link, gnu-mcu-eclipse.github.io/.../ , to setup my debug environment before. I was able to view the registers. However, I updated my eclipse and the SVD...
I use the nRF52-SDK on an nRF52840 PDK, but if I start a scan request, I don't get the number of scanned channels back in the mlme_scan_conf_t.
I.e. mlme_scan_conf_t::unscanned_channels...
Hi! I need to understand the basic functionality of BLE Mesh.
Please see attached picture.
1. Is it true that a device (eg BLUE) through BLE mesh can communicate DATA...
Dear friends,
Software &Hardware: Power Profiling Application (a SDK example), S132 softdevice, nRF52832(PCA10040), Power Monitor. The measured average current consumptions...
What is the maximum sampling rate of nrf52832? I used the ppi on nrf52632 to collect the signal on gpio. After testing, it was found that when the signal on gpio is greater...
Hello all,
I want to built a coin cell powered thermometer with NTC thermistor.
May I know if I need to regulate the voltage from the coin cell or i can power the nrf52832...
I have a problem with the 802.15.4 software part of my nRF52840 PDK. I wanted to replace our current 802.15.4 hardware parts from TI with the new nRF52840, due to the lack...
Hello. We are now starting our review to customize code for the pending use of the Nordic devices in low power mode. Have a mix of Nordic kits now. Using the nRF52832 (PCA10040...
Hi,
I am trying to implement buttonless DFU by following the ble_app_hrs example provided in the SDK and modifying the bootloader (nRF51_SDK_10.0.0\examples\ble_peripheral...
We have our custom PCB design that we program and debug by connecting the SWD lines to nrf51 DK's SWD. We wanted to use trace for better debugging options, however we discovered...
Hi,
I have a task to do PWM frequency repeater on nrf52832. After reading forums I decided to make it with PPI, 2 GPIOTE and 3 Timers. Here what I did: https://github...
Hello everybody,
I used SDK14.2 S132
I defined fds_write and read function like that;
Also, I wrote a function to register particular data;
Then I used save_data...
Hi, I followed through this tutorial:
https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
But to my frustration I realized...
