Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I am using saadc to periodically sample a voltage (per about 12 seconds). The voltage cannot be shutdown and always is a value neigher zero nor VDD (1.25v, 2.5v, 1.0v, etc...
Hi,
I'm wondering if the DTM mode can be entered over the air interface on nRF bluetooth products, as specified by Core4.2 [Vol2 Part C] 4.7.1 Activation and Deactivation...
Hi,
I am looking for an solution which requires to have an BT dual mode(Smart Ready) SoC. As i require the high data rate of 2.1 and also require support of BLE 4.0.
...
HI ,
I need to interface particle measurement sensor with nrf52832. I am using S132 softdevice and SDK 11.0 for my application. I need to send commands to sensor to take...
Hi,
I feel myself a bit silly...my nRF52840 board was working the last few weeks nicely, it was visible both in nRFgo and Keil. I had the board some time in button cell...
Hello, after downloading my user app using keil, I can't seem to erase the whole chip.
This is what I'm trying to do:
erase the whole chip (nrf52840).
program S140...
Hello, when migrating a project from nrf51 to S140 nrf52840, I got an
"Error: L6218E: Undefined symbol app_error_fault_handler (referred from softdevice_handler.o)."
...
Hi,
I am quite a beginner about nrf51822. I understand that I can get RSSI during advertise mode before pairing. But I am not sure I can get RSSI after pairing. Can I get...
Hi, everyone.
Now I have found some posts about the development enviroment on Mac OS X. But none of them describes clearly how to setup the development enviroment with an...
We are trying to get serial bootloader (DFU) working. I compiled a debug version of the experimental_bootloader_secure_serial in SDK13.0.0 to see what really happens there...
Hello,
I am successfully using the following code:
float f = 23.50
char buffer[10];
sprintf(buffer, "Float = %f\n", f);
SEGGER_RTT_WriteString(0, buffer);
I...
Can nRF51 be BLE connected while it's on sleep mode? (connected by other device as Peripheral mode)
I thought, to be connected as peripheral mode, It must be advertising...
Dear Nordic Team,
We have a customer that would like us to extend an C# desktop application to use serial over BLE. What is the best dongle firmware and Windows driver...
