As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ?
Trying to build this gets...
Hello,
I am currently testing the `ipt_initiator` sample on the nRF54L15-DK v1.0.0 using nRF Connect SDK v3.3.1.
When I call `k_sleep()` inside the loop in the `main(...
Hi guys,
I got very strange problem:
I got 2 units:
1) "Tester" board (which is a CENTRAL)
2) "TOP" board (which is PHERIPHERAL)
The "Tester" get commands...
Hi,
1.Can the sQSPI and SPI functions of nRF54L15 operate simultaneously at 32 MHz on the P2 port? 2.Can the sEMMC and SPI of nRF54L15 operate simultaneously at 32 MHz on...
I am using the nRF5340 development board to program the LBS example from the NCS SDK2.7. After system-off, the current is still several tens of microamps, which differs from...
Hei!
I can't seem to get my devicetree overlay to properly work. I have an external LED and two buttons connected to the GPIO ports mentioned in the overlay, and I've...
Bros, I had updated ncs sdk from v3.1.1 to v3.3.1 today, and when I rebuild an nrf5340 project found that NETAPP ram overflowed, and the error could be represented by build...
Hi,
We have come across AT%XRFTEST command problem for TX test on nRF9151 EVK. We have used nRF9151 modem firmware version 2.0.2 and executed following AT command on nRF9151...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hello, I am trying to convert my codebase from segger embedded studio to nrf connect. I am currently working on the spi section of my codebase.
I am communicating from...
Using SDK 2.4.2
1) Is there a way to specify multiple MCUBoot keys in the same way they can be specified for NSIB? MCU Boot allows an array of keys, but it looks like zephyr...
Hi! Do people actually use the 2.2-4.7Ohm series resistor on the VBUS input to the nRF5340? It's just such a low resistance, I don't particularly see the point. Thanks!
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi,
I want to set my BLE advertising as public adress Dynamic, and can't work. I have try reboot,, and call "bt_ctlr_set_public_addr" before "bt_enable", It is working first...
